Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Trailer Brake Controller Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Trailer Brake Controller Communication Stop Mode Either condition is met:
·

"Trailer Brake Controller" is not displayed on the "Bus Check" screen.

·

"Brake Control with Bracket Relay Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside brake control with bracket relay

·

Brake control with bracket relay CAN branch wire or connector

·

Brake control with bracket relay



For vehicles with a trailer brake control system.


WIRING DIAGRAM

C352761E01
1.646,0.875 1.75,1.073 0.104,0.198 10 false 7 1.646,1.469 1.813,1.667 0.167,0.198 10 false 18 0.417,1.969 0.656,2.167 0.24,0.198 10 false J75 0.406,2.146 1.948,2.344 1.542,0.198 10 false No. 1 Junction Connector 5.313,1.49 5.479,1.688 0.167,0.198 10 false 10 5.354,0.896 5.469,1.094 0.115,0.198 10 false 4 5.594,1.01 6.01,1.198 0.417,0.188 10 false CANH 5.604,1.594 6.021,1.781 0.417,0.188 10 false CANL 5.573,2.521 5.792,2.719 0.219,0.198 10 false +B 5.354,2.385 5.5,2.552 0.146,0.167 10 false 8 5.354,3.208 5.5,3.375 0.146,0.167 10 false 2 5.573,3.313 5.792,3.51 0.219,0.198 10 false IG 5.604,4.146 5.917,4.354 0.313,0.208 10 false GND 5.365,4.031 5.49,4.198 0.125,0.167 10 false 5 5.313,4.802 5.635,4.99 0.323,0.188 10 false J156 5.323,4.99 6.969,5.365 1.646,0.375 10 false Brake Control with Bracket Relay 3.969,2.323 4.656,2.51 0.688,0.188 10 false TOW BRK 3.948,3.104 4.771,3.302 0.823,0.198 10 false ECU-IG No.1 2.219,2.5 3.01,2.698 0.792,0.198 10 false from Battery 1.781,3.323 2.99,3.521 1.208,0.198 10 false from IG No.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE CONTROL WITH BRACKET RELAY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE CONTROL WITH BRACKET RELAY CAN BRANCH WIRE)
a.
U152659E01
1.526,0.315 1.856,0.456 0.330,0.141 10 J156 2.32,1.513 2.572,1.73 2.572,1.73 2.729,1.73 false 2.32,1.093 2.572,0.876 2.572,0.876 2.729,0.876 false 0.133,0.08 0.585,0.222 0.452,0.141 10 *a 2.756,0.799 3.180,0.940 0.424,0.141 10 CANH 2.756,1.646 3.156,1.787 0.400,0.141 10 CANL

Disconnect the J156 brake control with bracket relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J156-4 (CANH) - J156-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Control with Bracket Relay)



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE CONTROL WITH BRACKET RELAY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BRAKE CONTROL WITH BRACKET RELAY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (BRAKE CONTROL WITH BRACKET RELAY - BATTERY AND BODY GROUND)
a.
U152660E01
1.166,1.52 0.925,1.829 0.925,1.829 0.767,1.829 false 1.166,1.52 0.925,1.829 0.925,1.829 0.767,1.829 false 1.873,1.489 1.993,2.007 1.993,2.007 2.151,2.007 false 0.334,1.753 0.786,1.894 0.452,0.141 10 GND 0.515,0.635 0.966,0.777 0.452,0.141 10 IG 2.202,1.91 2.654,2.051 0.452,0.141 10 +B 1.526,0.315 1.856,0.456 0.330,0.141 10 J156 1.32,1.093 0.902,0.71 0.902,0.71 0.744,0.71 false 0.133,0.08 0.585,0.222 0.452,0.141 10 *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J156-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J156-8 (+B) - Body ground Always 11 to 14 V
J156-2 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Brake Control with Bracket Relay)


OK

REPLACE BRAKE CONTROL WITH BRACKET RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR