The engine has two temperature sensors, an Engine Coolant Temperature (ECT) sensor and an Intake Air Temperature (IAT) sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection time and the ignition timing to control the engine.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P011B | All of the following conditions are met (2 trip detection logic): 1.
The battery voltage is 10.5 V or higher. 2.
7 hours or more have elapsed from engine stop on the previous trip. 3.
15 seconds*1 or 102 seconds*2 after a cold engine start. 4.
The minimum Intake Air Temperature (IAT) after the engine starts is higher than -10°C (14°F). 5.
The average Engine Coolant Temperature (ECT) before the engine starts is higher than -10°C (14°F). 6.
The difference between the readings of ECT and IAT is higher than 25°C (45°F). |
·
IAT sensor ·
ECT sensor ·
ECM |
*1: for 100 L (26.4 US gal) Fuel Tank
*2: for 144 L (38 US gal) Fuel Tank
Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the ECT and IAT are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, this does not necessarily indicate a fault.
The ECM monitors the difference between the Engine Coolant Temperature (ECT) and the Intake Air Temperature (IAT) when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine started cold after 7 hours or more have elapsed since the engine was stopped (ignition switch turned off) on the previous trip. If the difference between the ECT and the IAT on a cold start exceeds 25°C (45°F), the ECM interprets this as a malfunction in the ECT sensor circuit and IAT sensor circuit, and stores the DTC.
| Related DTCs | P011B: Engine Coolant Temperature (ECT) / Intake Air Temperature (IAT) sensor correlation |
| Required Sensors/Components (Main) | ECT / IAT sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per driving cycle |
| Duration | - |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not stored | None |
| All of following conditions met | Conditions 1 and 2 |
| 1. All of following conditions met | Conditions (a), (b), (c) and (d) |
| (a) After ignition switch ON and engine not running time | Less than 20 seconds |
| (b) Soak Time | 7 hours or more |
| (c) Battery voltage | 10.5 V or higher |
| (d) Time after engine start | ·
15 seconds or more (for 100 L (26.4 US gal) Fuel Tank) ·
102 seconds or more (for 144 L (38 US gal) Fuel Tank) |
| 2. Either of the following conditions are met | Condition (a) and (b) |
| (a) Minimum IAT after engine start | -10°C (14°F) or higher |
| (b) ECT before engine start | -10°C (14°F) or higher |
| MAF sensor circuit fail (P0102, P0103) | Not detected |
| IAT sensor circuit fail (P0112, P0113) | Not detected |
| ECT sensor circuit fail (P0115, P0117, P0118, P0125) | Not detected |
| Soak timer circuit fail (P2610) | Not detected |
| Deviated temperature (difference between ECT and IAT) | Below -25°C (-45°F) or higher than 25°C (45°F) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) [A].
Turn the ignition switch off.
With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].
Start the engine and wait 60 seconds or more [C].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P011B.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P011B | A |
| P011B and other DTCs | B |
If any DTCs other than P011B are output, troubleshoot those DTCs first.
A
B
Leave the vehicle for 7 hours or more.
It is necessary leave the vehicle for 7 hours or more to allow conditions similar to the DTC detection conditions.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.
Read the value displayed on the Techstream.
Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).
Temperature readings on the vehicle outside temperature gauge (if equipped) are not suitable for comparing to the IAT reading. The outside temperature gauge has a significant delay built-in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.
Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / All Data / Coolant Temp.
Read the value displayed on the Techstream.
The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).
If the result is not as specified, check that there are heat sources such as a block heater in the engine compartment.
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG