The ECM detects the signal from the transfer indicator switch.
This DTC indicates that the transfer indicator switch (L4) remains on.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2772 | Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm. (b) Transfer position switch is in 2WD or 4H. |
·
Short in transfer indicator switch (L4) circuit ·
4 wheel drive control ECU ·
ECM |
The ECM monitors the transfer-case transfer indicator switch to determine when the transfer-case 4L gears are engaged. If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the transfer indicator switch, illuminate the MIL and store the DTC:
The transfer indicator switch indicates that the 4L transfer-case gears are engaged.
The transfer-case shifter is in the "2WD" or "4H" position.
The transfer-case output shaft speed is between 1000 and 3000 rpm.
The specified time period has elapsed.
| Related DTCs | P2772: Transfer indicator switch/Rationality fault diagnostics |
| Required sensors/Components | Transfer indicator switch |
| Frequency of operation | Continuous |
| Duration | ON malfunction (A): 1.8 seconds
ON malfunction (B): 0.5 seconds |
| MIL operation | 1 driving cycle |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0500 (Vehicle speed sensor "A" circuit) |
| Output speed sensor circuit | Not circuit malfunction |
| Transfer neutral position switch | OFF |
| Output speed (Transfer output speed) | 1000 rpm or more, and less than 3000 rpm |
| Output speed (Transfer output speed) | 143 rpm or more |
Both of the following conditions are met: ON malfunction (A) and (B)
| Transfer indicator switch (L4) | ON |
| Actual transfer gear ratio
Transfer input speed / Transfer output speed |
0.9 or more, and less than 1.1 |
Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
Disconnect the D70 transfer indicator switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D70-2 (L4) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Transfer Indicator Switch) |
OK
(See pageDrivetrain>WF1AM TRANSFER>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the D70 transfer indicator switch connector.
Disconnect the A26 4 wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A26-13 (L4) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
OK
(See pageDrivetrain>WF1AM TRANSFER>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the D70 transfer indicator switch connector.
Disconnect the A26 4 wheel drive control ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-21 (L4) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG