Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.08
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234043 ENGINE UNIT A

1UR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

A214796E01
1.722,2.237 2.976,2.425 1.254,0.188 10 24.5 mm (0.965 in.) 1.587,2.937 2.780,3.125 1.193,0.188 10 40 mm (1.58 in.) 1.9,2.578 3.078,2.766 1.178,0.188 10 14 mm (0.551 in.) 1.05,2.752 1.484,2.326 1.484,2.326 1.68,2.326 false 1.049,3.171 1.449,2.671 1.449,2.671 1.868,2.671 false

a.

Install the timing chain cover stud bolt.

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.
A165519E03
0.656,3.344 0.865,3.948 0.865,3.948 0.656,3.719 false 2.281,3.76 2.594,3.979 false 1.917,2.979 2.115,2.979 2.115,2.979 2.281,3.427 false 1.438,0.094 1.583,0.281 0.146,0.188 10 false A 0.156,1.156 0.302,1.344 0.146,0.188 10 false A 2.125,2.25 2.302,2.458 0.177,0.208 10 false B 0.271,3.969 1.417,4.167 1.146,0.198 10 false 9 mm (0.354 in.) 0.969,3.333 1.677,3.771 0.708,0.438 10 false 19 mm (0.748 in.) 1.917,4 3.063,4.198 1.146,0.198 10 false 12 mm (0.472 in.) 0.5,2.885 1.677,3.146 1.177,0.26 10 false 22 mm (0.866 in.) 2.615,3.323 3.271,3.719 0.656,0.396 10 false 39 mm (1.54 in.) 0.271,2.563 0.469,2.76 0.198,0.198 10 false A: 1.896,2.563 2.063,2.76 0.167,0.198 10 false B:

Install the oil pan stud bolt.

i.

Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 2.INSTALL RING PIN

A214797E03
0.448,1.479 0.583,1.646 0.135,0.167 10 false A 0.667,1.958 0.802,2.125 0.135,0.167 10 false A 2.854,1.458 2.979,1.625 0.125,0.167 10 false B 2.875,1.844 3,2.01 0.125,0.167 10 false B 0.375,2.948 1.385,3.146 1.01,0.198 10 true 7.5 to 8.5 mm 1.948,2.958 2.844,3.156 0.896,0.198 10 true 3.6 to 4.6 mm 0.448,2.333 0.625,2.5 0.177,0.167 10 false A: 1.896,2.333 2.052,2.5 0.156,0.167 10 false B:

a.

Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard Protrusion:
Item Ring Pin Diameter Specified Condition
Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)
Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)



Hide 11381A 3.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A148433E01
0.141,0.746 0.509,0.988 0.367,0.242 10 SST 1.132,0.981 0.512,0.846 0.512,0.846 1.052,1.52 false

Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the oil seal at an angle.




Hide 12109A 4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

A160728

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the drain pipe.


c.

Install the oil drain pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381 5.INSTALL ENGINE REAR OIL SEAL RETAINER

A148434E11
0.396,1.719 0.354,1.469 false 3.083,1.698 3.063,1.469 false 0.771,0.094 2.698,0.281 1.927,0.188 10 false Seal diameter: 2.0 to 3.0 mm 2.844,1.688 3.333,1.865 0.49,0.177 10 false 3.5 mm 0.135,1.677 0.625,1.854 0.49,0.177 10 false 3.5 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Application position from inside edge of retainer:

3.5 mm (0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the engine rear oil seal retainer within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A145612

Install the oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.




Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

A160724

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil strainer.


c.

Install the oil strainer with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the O-ring is not twisted or damaged.



Hide 12121 7.INSTALL NO. 1 OIL PAN BAFFLE PLATE

A160723

a.

Install the baffle plate with the 7 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12101 8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

A160729E04
0.531,0.052 2.479,0.479 1.948,0.427 10 true Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160721E04
3.094,1.063 3.229,1.219 0.135,0.156 10 false A 2.313,1.781 2.448,1.938 0.135,0.156 10 true B 2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.802 1.427,1.115 0.281,0.313 10 true Nut 3.083,0.698 3.219,0.854 0.135,0.156 10 false A 1.875,1.823 2.01,1.979 0.135,0.156 10 true B 1.479,1.833 1.615,1.99 0.135,0.156 10 true B 1.188,1.833 1.323,1.99 0.135,0.156 10 true B 0.896,1.792 1.031,1.948 0.135,0.156 10 true B 0.302,1.458 0.438,1.615 0.135,0.156 10 false B 2.99,0.26 3.125,0.417 0.135,0.156 10 false B 2.219,0.021 2.354,0.177 0.135,0.156 10 false B 1.875,0.021 2.01,0.177 0.135,0.156 10 false B 1.438,0.031 1.573,0.188 0.135,0.156 10 false B 0.979,0.031 1.115,0.188 0.135,0.156 10 false B 0.292,0.26 0.427,0.417 0.135,0.156 10 false B

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12102A 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

A160730E01
0.516,0.049 2.388,0.232 1.872,0.184 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.156 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160720E02
2.885,0.531 3.156,0.708 0.271,0.177 10 false Nut 1.448,1.698 1.719,1.875 0.271,0.177 10 true Nut

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 16877 10.INSTALL NO. 1 HEAT EXCHANGER COVER

A214798E01
0.508,0.14 2.371,0.331 1.862,0.191 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A214631E06
2.51,1.875 2.75,2.021 0.24,0.146 9 false Nut 0.271,1.74 0.51,1.885 0.24,0.146 9 true Nut 0.385,0.281 0.521,0.448 0.135,0.167 10 true A 0.042,1.365 0.177,1.531 0.135,0.167 10 true B 3.01,1.719 3.146,1.885 0.135,0.167 10 true C 1.146,0.167 1.281,0.333 0.135,0.167 10 true A 1.74,0.177 1.875,0.344 0.135,0.167 10 true A 2.167,0.177 2.302,0.344 0.135,0.167 10 true A 2.823,0.219 2.958,0.385 0.135,0.167 10 true A 3.26,0.333 3.396,0.5 0.135,0.167 10 true A 1.021,1.854 1.156,2.021 0.135,0.167 10 false A 1.646,1.865 1.781,2.031 0.135,0.167 10 false A 2,1.854 2.135,2.021 0.135,0.167 10 true A 3.271,1.542 3.406,1.708 0.135,0.167 10 true A

Install the heat exchanger cover with the 12 bolts and 2 nuts.

Torque:
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 20 mm (0.787 in.) 8 mm (0.315 in.)
Bolt B 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt C 16 mm (0.630 in.) 6 mm (0.236 in.)


NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12203A 11.INSTALL VENTILATION PIPE GASKET

A214799E02
0.75,1.427 0.75,1.156 0.75,1.156 1.24,1.156 true 0.552,1.427 1.24,1.427 true 0.188,1.344 0.5,1.531 0.313,0.188 10 true SST

a.

Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the gasket at an angle.

·

Do not tap the gasket excessively.




Hide 12209E 12.INSTALL OIL RETURN PIPE GASKET

A217533

a.

Install a new oil return pipe gasket.


Hide 11445 13.INSTALL CYLINDER BLOCK WATER JACKET SPACER

A214628E01
0.032,0.152 0.599,0.341 0.567,0.188 10 Up Mark 0.709,0.239 0.857,0.239 0.857,0.239 2.485,0.772 false 0.854,0.888 0.854,0.243 false

a.

Install the 2 water jacket spacers as shown in the illustration.

NOTICE:
·

Face the cutouts indicated by the arrows in illustration away from the engine.

·

Face the "up mark" as shown in the illustration.




Hide 13716 18.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 32 valve stem caps to the cylinder head.


Hide 13750 19.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

b.

Install the 32 valve lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster at the same place it was removed from.



Hide 13801 20.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the lash adjuster tips and valve stem cap ends.


b.
A386787E01
0.74,1.042 0.823,1.042 0.823,1.042 1.031,1.094 false 2.094,0.188 1.865,0.188 1.865,0.188 1.615,0.396 false 2.458,1.125 2.667,1.125 true 2.146,0.094 3.365,0.281 1.219,0.188 10 false Valve Rocker Arm 2.708,1.031 3.417,1.385 0.708,0.354 10 false Valve Lash Adjuster 0.01,0.948 0.771,1.344 0.76,0.396 10 false Valve Stem Cap

Install the 32 valve rocker arms as shown in the illustration.


Hide 13521A 25.INSTALL CRANKSHAFT TIMING GEAR KEY

A214836

a.

Install the timing gear key.

HINT:

The other timing gear key will be installed at a later step.



Hide 37.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION

a.

Temporarily install the pulley set bolt.


b.

Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.


c.

Remove the crankshaft pulley set bolt.

A214603E06
3.49,4.813 4.021,5.063 4.021,5.063 4.021,5.177 false 3.656,4.385 4.042,4.01 4.042,4.01 4.167,4.01 true 0.646,0.271 0.458,0.271 0.458,0.271 0.552,0.917 true 1.51,0.271 1.729,0.271 1.729,0.271 1.656,0.813 true 5.635,0.323 5.469,0.323 5.469,0.323 5.552,0.823 true 6.51,0.323 6.76,0.323 6.76,0.323 6.708,0.938 true 0.542,5.552 0.813,6.104 0.813,6.104 1.365,5.552 false 0.333,4.417 0.229,4.417 0.229,4.417 0.531,5.365 false 0.531,3.396 1.052,4.104 1.052,4.104 1.375,3.49 false 5.854,5.552 6.115,6.135 6.115,6.135 6.583,5.552 false 5.323,4.677 5.073,4.677 5.073,4.677 5.542,5.26 false 6.375,4.438 6.885,4.438 6.885,4.438 6.615,5.365 false 5.469,3.708 6,4.125 6,4.125 6.458,3.5 true 0.604,3.219 0.354,2.385 0.354,2.385 0.458,2.385 false 1.74,3.177 2.042,2.385 2.042,2.385 1.906,2.385 false 5.406,3.229 5.177,2.448 5.177,2.448 5.271,2.448 true 6.552,3.281 6.854,2.49 6.854,2.49 6.708,2.49 true 1.396,5.375 1.74,4.958 1.74,4.958 1.646,4.958 false 1.667,5.26 2.083,4.688 2.083,4.688 1.99,4.688 false 1.813,5.229 2,5.448 2,5.448 2,5.719 false 5.427,5.229 5.313,5.385 5.313,5.385 5.313,5.615 false 5.563,4.906 5.448,4.906 5.448,4.906 5.813,5.365 false 3.625,5.198 4.479,5.365 0.854,0.167 10 false Timing Mark 4.24,3.917 4.552,4.115 0.313,0.198 10 false Key 0.698,0.198 1.531,0.375 0.833,0.177 10 false Timing Mark 5.719,0.25 6.552,0.427 0.833,0.177 10 false Timing Mark 0.198,6.104 1.573,6.313 1.375,0.208 10 false Timing Mark Position 0.521,4.104 1.771,4.313 1.25,0.208 10 true Knock Pin Position 5.385,4.594 6.615,4.844 1.229,0.25 10 false Approximately 45° 5.615,4.823 6.844,5.073 1.229,0.25 10 false Approximately 32° 5.5,6.135 6.875,6.344 1.375,0.208 10 false Timing Mark Position 5.438,4.115 6.688,4.323 1.25,0.208 10 true Knock Pin Position 0.552,2.302 1.927,2.479 1.375,0.177 10 false Timing Mark Position 5.354,2.354 6.729,2.531 1.375,0.177 10 false Timing Mark Position 0.365,4.333 1.594,4.583 1.229,0.25 10 true Approximately 2° 0.49,4.854 1.719,5.104 1.229,0.25 10 false Approximately 16° 0.802,4.594 1.948,4.781 1.146,0.188 10 true Approximately 45° 1.708,5.719 2.198,6.094 0.49,0.375 10 false Toward Ceiling 5.031,5.615 5.521,5.99 0.49,0.375 10 false Toward Ceiling 5.177,4.313 6.406,4.615 1.229,0.302 10 true Approximately 18° 3.104,1.063 4.125,1.438 1.021,0.375 10 false Toward Ceiling


Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 41.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A163995E05
1.771,2.635 1.854,3.01 false 1.854,3.01 1.927,2.604 false 1.688,3.031 2.01,3.208 0.323,0.177 10 true SST

Apply MP grease to the lip of a new oil seal.


b.

Using SST and a hammer, tap in the oil seal to a depth between 0 to 1.0 mm (0 to 0.0394 in.) from the timing chain cover edge.

SST
09223-22010  
09506-35010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap oil seal at an angle.




Hide 13521A 42.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A163993

Install the crankshaft timing gear key to the crankshaft.


Hide 11193 43.INSTALL SPARK PLUG TUBE GASKET

A380019E01
0.552,1.885 2.844,2.083 2.292,0.198 10 false Area to cut off

a.

Using a cutter knife, cut off the seal part of the removed gasket.


b.
A164316E03
1.167,0.583 1.271,0.333 1.271,0.333 1.396,0.333 true 1.688,1.156 1.688,1.5 true 1.448,0.271 2.615,0.5 1.167,0.229 10 false Removed Gasket 1.333,1.583 2.188,1.792 0.854,0.208 10 false New Gasket

Using the removed gasket and a hammer, tap in a new gasket until it stops.

HINT:

If the removed gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the gasket lip.


d.

Return the 4 ventilation baffle plate claws to the original positions.


Hide 15678A 44.INSTALL OIL CONTROL VALVE FILTER

A164313E06
2.479,0.885 2.479,1.302 false 2.813,0.104 2.969,0.104 2.969,0.104 3.125,0.885 false 1.688,0.417 2.146,0.417 2.146,0.417 2.792,0.792 false 2.313,1.302 2.708,1.542 0.396,0.24 10 false Filter 1.208,0.344 1.75,0.531 0.542,0.188 10 true Gasket 1,0.052 2.854,0.26 1.854,0.208 10 true Cylinder Head Cover Spacer

a.

LH:

i.

Install the valve filter in the cylinder head cover.


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A164314E05
0.917,0.781 0.917,1.208 false 0.281,0.781 0.635,0.104 0.635,0.104 0.771,0.104 true 0.625,0.677 0.99,0.396 0.99,0.396 1.917,0.396 true 0.75,1.229 1.125,1.438 0.375,0.208 10 false Filter 1.958,0.292 2.458,0.5 0.5,0.208 10 true Gasket 0.802,0 2.656,0.292 1.854,0.292 10 true Cylinder Head Cover Spacer

RH:

i.

Install the valve filter in the cylinder head cover.


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 11201 45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A162526

Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).


b.

Install the cover gasket to the cylinder head cover.

NOTICE:

Remove any oil from the contact surface.



c.
A162547E01
0.348,1.738 1.203,1.925 0.855,0.187 10 Seal Packing

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A210023E02
1.417,1.469 1.563,1.646 0.146,0.177 10 true A

Install the cylinder head cover washer with a new seal and the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11202 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A162524

Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).


b.

Install the cover gasket to the cylinder head cover.

NOTICE:

Remove any oil from the contact surface.



c.
A162546E07
0.354,1.76 1.229,1.948 0.875,0.188 10 false Seal Packing

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A210021E03
1.938,1.479 2.083,1.656 0.146,0.177 10 true A

Install the cylinder head cover washer with a new seal and the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 15330B 47.INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY

a.
A214600

LH:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A214601

RH:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 15100R 48.INSTALL CRANKSHAFT POSITION SENSOR

A161908

a.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19312 49.INSTALL CRANKSHAFT POSITION SENSOR PROTECTOR

A161907

a.

Install the sensor protector with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 50.INSTALL CAMSHAFT POSITION SENSOR

A214599

a.

Install the camshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 51.INSTALL VVT SENSOR

a.
A214597

LH:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A214598

RH:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 19100P 52.INSTALL SPARK PLUG

a.

Using a 16 mm plug wrench, install the 8 spark plugs.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12185 53.INSTALL OIL FILLER CAP HOUSING

a.
A161917

Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.


b.
A214596

Install the cap housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 54.INSTALL OIL FILLER CAP SUB-ASSEMBLY