Home › Drivetrain › K320 (MULTIDRIVE / CVT) › OIL PAN
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438031 OIL PAN A

K320 MULTIDRIVE / CVT  OIL PAN  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446030N03
4.615,2.51 4.948,2.51 false 0.99,2.323 1.156,2.323 1.156,2.323 1.406,1.906 false 6.469,0.292 6.802,0.292 false 0.813,2.146 1.094,2.5 0.281,0.354 18 false 1 4.417,2.354 4.698,2.708 0.281,0.354 18 false 2 6.26,0.135 6.542,0.49 0.281,0.354 18 false 3 2.979,3.01 3.292,3.208 0.313,0.198 10 false x4 2.135,2.833 2.448,3.031 0.313,0.198 10 false x4 3.677,2.813 3.99,3.01 0.313,0.198 10 false x9 5.948,2.573 6.26,2.771 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 ENGINE UNDER COVER LH 51442C - - -
3 DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID - - (Click here) -

C446038N01
4.021,0.583 4.354,0.583 false 4.052,1.01 4.385,1.01 false 4.094,1.51 4.427,1.51 false 4.417,0.438 4.698,0.792 0.281,0.354 18 false 4 4.458,0.854 4.74,1.208 0.281,0.354 18 false 5 4.5,1.354 4.781,1.708 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

4 AIR CLEANER CAP WITH AIR CLEANER HOSE 17705 - - -
5 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
6 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -

C428863N05
2.75,2.417 3.083,2.417 false 1.667,2.667 2,2.667 false 1.5,2.531 1.813,2.865 0.313,0.333 18 false 7 3.135,2.292 3.448,2.625 0.313,0.333 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

7 ENGINE WIRE 82121 - - -
8 WIRE HARNESS CLAMP BRACKET - - - -

C430089N02
2.25,4.083 2.531,4.417 2.531,4.417 2.667,4.417 false 4.75,4.323 5.083,4.323 false 4.281,3.99 4.615,3.99 false 5.75,2.656 6,2.323 6,2.323 6.167,2.323 false 2.583,2.417 2.75,2.417 2.75,2.417 2.802,2.635 false 4.75,3.75 5.083,3.75 false 5.938,2.75 6.271,2.75 false 1.365,2.844 1.823,3.042 0.458,0.198 10 false x11 2.917,4.292 3.365,4.604 0.448,0.313 18 false 9 5.125,4.271 5.583,4.469 0.458,0.198 10 false *2 4.094,3.938 4.552,4.135 0.458,0.198 10 false ● 5.135,3.688 5.594,3.885 0.458,0.198 10 false *3 6.313,2.688 6.771,2.885 0.458,0.198 10 false *1 6.208,2.26 6.667,2.458 0.458,0.198 10 false ● 2.427,2.354 2.885,2.552 0.458,0.198 10 false ● 2.708,4.354 3.167,4.552 0.458,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

9 TRANSAXLE SIDE COVER SUB-ASSEMBLY 35015Y - - -

*1 REFILL PLUG *2 OVERFLOW PLUG
*3 OVERFLOW (CVT) TUBE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transaxle side cover sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Air intake system parts Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 2.REMOVE ENGINE UNDER COVER LH

Hide 3.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C431778C01
4.5,2.75 4.24,2.75 true 4.083,2.677 4.396,2.833 0.313,0.156 10 false *1 0.615,0.125 1.115,0.396 0.5,0.271 18 true i, vi 4.042,0.094 4.469,0.375 0.427,0.281 18 true ii, v 2.167,2.063 2.667,2.333 0.5,0.271 18 true iii, iv
*1 Overflow (CVT) Tube - -


i.

Remove the refill plug and gasket from the rear transaxle case sub-assembly.


ii.

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly.


iii.

Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly.


iv.

Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


v.

Using a 10 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle case sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



vi.

Temporarily install the gasket and refill plug to the rear transaxle case sub-assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.




Hide 17705 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 82121 7.REMOVE ENGINE WIRE

a.
C430076


Hide 8.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C430077


Hide 35015Y 9.REMOVE TRANSAXLE SIDE COVER SUB-ASSEMBLY

a.
C430078