| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 39 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| ★ | Precoated part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
|
|
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
28800
5.REMOVE BATTERY
6.REMOVE FRONT WHEELS
51410
7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442C
8.REMOVE ENGINE UNDER COVER LH
51441C
9.REMOVE ENGINE UNDER COVER RH
51447D
10.REMOVE CENTER NO. 4 ENGINE UNDER COVER
14.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55735A
15.REMOVE WATER GUARD PLATE LH
55815E
16.REMOVE NO. 1 FRONT VENTILATOR SEAL
55701J
17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
17705
18.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17801
19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
74404A
22.REMOVE BATTERY CLAMP SUB-ASSEMBLY
82662A
23.REMOVE NO. 1 RELAY BLOCK COVER
24.DISCONNECT WIRE HARNESS
16571C
25.DISCONNECT NO. 1 RADIATOR HOSE
16572D
26.DISCONNECT NO. 2 RADIATOR HOSE
23826
29.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
77261D
30.DISCONNECT FUEL TANK TO CANISTER TUBE
16290F
31.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
87245
32.DISCONNECT INLET HEATER WATER HOSE
23901
33.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
88711
34.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
35.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
45259A
37.REMOVE COLUMN HOLE COVER SILENCER SHEET
40.REMOVE FRONT DRIVE SHAFT ASSEMBLY
11361J
41.REMOVE FLYWHEEL HOUSING UNDER COVER
43.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
1. Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
12353
44.REMOVE ENGINE MOUNTING BRACKET CAP
Turn over the engine mounting bracket cap to the upper part.
While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.
45.INSTALL ENGINE HANGERS
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
1. Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
12372A
46.REMOVE ENGINE MOUNTING INSULATOR LH
|
|
12305
47.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
|
|
48.REMOVE WATER HOSE
28100
49.REMOVE STARTER ASSEMBLY
11363A
50.REMOVE FLYWHEEL HOUSING SIDE COVER
82121
51.REMOVE ENGINE WIRE
30400
52.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
19315
54.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
16620D
56.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
27020
57.REMOVE GENERATOR WITH REGULATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 80A Type)>REMOVAL
for 100A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 100A Type)>REMOVAL
59.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
60.REMOVE ENGINE HANGERS