| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane tracing assist system, road sign assist system, pre-collision system or lighting system may not operate properly due to a difference in the transmissivity or black ceramic border.
56115A
1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER
| *1 | No. 1 windshield glass stopper | - | - |
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56111
2.CLEAN WINDSHIELD GLASS
| *A | When reusing the Windshield Glass | - | - |
When reusing the windshield glass:
1. Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean it with a non-residue solvent.
56116C
3.INSTALL NO. 2 WINDSHIELD GLASS STOPPER
When reusing the windshield glass:
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| *c | Windshield Glass Edge Side | *d | Center of Stopper |
Using a brush or sponge, coat the installation area of the No. 2 windshield glass stoppers with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
2. Install the 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 13.7 to 14.7 mm (0.539 to 0.579 in.) |
Allow the glass primer to dry for 3 minutes or more.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56117A
4.INSTALL WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass:
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
Using a brush or sponge, coat the installation area of the window glass adhesive dam with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install a new window glass adhesive dam to the windshield glass as shown in the illustration.
75533G
5.INSTALL WINDSHIELD OUTSIDE MOULDING
When reusing the windshield glass:
| *a | Back Side of Windshield Glass | *b | Windshield Glass Edge Side |
Using a brush or sponge, coat the installation area of the windshield outside moulding with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install a new windshield outside moulding to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 1.15 to 2.65 mm (0.0453 to 0.104 in.) |
| b | 6.2 to 10.8 mm (0.244 to 0.425 in.) |
56111
6.INSTALL WINDSHIELD GLASS
|
Adhesive | - | - |
Clean and shape the contact surface of the vehicle body by the below procedure.
1. Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
2. Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.
| *a | Matchmark | *b | Suction Cup |
Prepare to install the windshield glass sub-assembly by the below procedure.
1. Using suction cups, place the windshield glass in the correct position.
2. Check that the whole contact surface of the windshield glass rim is perfectly even.
3. Align the matchmarks on the windshield glass and vehicle body.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
4. Remove the windshield glass.
5. Using a brush, coat the installation surface on the vehicle body with body primer.
Do not coat the adhesive with body primer.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.
| *1 | Window Glass Adhesive Dam | - | - |
| *a | Back Side of Windshield Glass | - | - |
|
Glass Primer | - | - |
Using a brush or sponge, coat the adhesive application area with glass primer as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 11 mm (0.433 in.) or more |
| b | 11 mm (0.433 in.) or more |
| c | 11 mm (0.433 in.) or more |
| d | 19 mm (0.748 in.) or more |
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
Apply glass primer to the ceramic notches.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
| *a | Sealer Gun | *b | Cartridge Nozzle |
|
Adhesive | - | - |
Prepare to apply adhesive to the windshield glass sub-assembly by the below procedure.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
1. Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 to 15.0 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11.0 mm (0.315 to 0.433 in.) |
2. Load the sealer gun with the cartridge.
| *1 | Window Glass Adhesive Dam | - | - |
| *a | Back Side of Windshield Glass | - | - |
|
Adhesive | - | - |
Apply adhesive to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 9.5 mm (0.374 in.) |
| c | 9.5 mm (0.374 in.) |
| d | 4.0 mm (0.157 in.) |
| *a | Matchmark | *b | Suction Cup |
Install the windshield glass by the below procedure.
1. Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass.
2. Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
3. Using a scraper, remove any excess or protruding adhesive.
4. Hold the windshield glass using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
7.INSPECT FOR LEAK
Inspect for leaks by the below procedure.
1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
2. If water leaks into the cabin, allow the water to dry and add adhesive.
3. Remove the protective tape.
63310
8.INSTALL ROOF HEADLINING ASSEMBLY
Return the front section of the roof headlining assembly to its original position.
Do not damage the roof headlining assembly or vehicle interior.
74612
9.INSTALL ASSIST GRIP COVER
74610S
10.INSTALL ASSIST GRIP ASSEMBLY
74348B
11.INSTALL VISOR HOLDER RH
74348C
12.INSTALL VISOR HOLDER LH
74310
13.INSTALL VISOR ASSEMBLY RH
74320
14.INSTALL VISOR ASSEMBLY LH
81260A
15.INSTALL MAP LIGHT ASSEMBLY
62212
17.INSTALL FRONT PILLAR GARNISH LH
62311B
18.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62312B
19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
87810
20.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
86401
21.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
8646C
22.INSTALL FORWARD RECOGNITION CAMERA
23.INSTALL WINDSHIELD WIPER MOTOR AND LINK
8646C
24.ADJUST FORWARD RECOGNITION CAMERA
If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.
Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.
Target Adjustment (One Time Recognition):
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Target Adjustment (Sequential Recognition):
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment:
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT