Home › Power Source / Network › POWER DISTRIBUTION › INTEGRATION RELAY › 2020.08–2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0438534 INTEGRATION RELAY A

POWER DISTRIBUTION  INTEGRATION RELAY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E448352N01
1.667,0.5 2,0.5 false 1.552,1.26 1.885,1.26 false 6.427,0.24 6.844,0.24 false 6.458,0.802 6.792,0.802 false 6.229,0.104 6.51,0.458 0.281,0.354 18 false 1 6.25,0.667 6.531,1.021 0.281,0.354 18 false 2 2.052,0.354 2.333,0.708 0.281,0.354 18 false 3 2.208,1.125 2.49,1.479 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 1 RELAY BLOCK COVER 82662A - - -
4 SEMICONDUCTOR POWER INTEGRATION ECU 82644 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the semiconductor power integration ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 82662A 3.REMOVE NO. 1 RELAY BLOCK COVER

a.
E437131


Hide 82644 4.REMOVE SEMICONDUCTOR POWER INTEGRATION ECU

Z101186

NOTICE:
·

Make sure the connector terminal is free from oil and grease.

·

Do not subject the semiconductor power integration ECU to any impact.

·

Do not use a semiconductor power integration ECU that has been dropped.

·

Do not disassemble the semiconductor power integration ECU.




a.
E448353C02
3.844,0.615 4.083,0.458 false 3.948,1.302 4.292,1.219 true 0.781,0.375 0.979,0.688 0.198,0.313 18 true i 6.177,1.146 6.385,1.438 0.208,0.292 18 true ii 3.781,0.073 3.969,0.344 0.188,0.271 18 true iii 3.719,0.604 4.031,0.802 0.313,0.198 10 false *a 3.76,1.24 4.073,1.438 0.313,0.198 10 false *a
*a Lock Lever - -


i.

Disengage the claws and pull up the semiconductor power integration ECU.


ii.

Disconnect the connector.


iii.

Disengage the claw and pull up the lock lever to disconnect the connector as shown in the illustration.