Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440543 ENGINE G

M15A-FXE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the power switch on (IG).


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Pre-procedure1

a.

Remove the air cleaner filter element sub-assembly.

HINT:

Click hereGeneral>MAINTENANCE>M15A-FXE AIR CLEANER FILTER ELEMENT>REMOVAL



Procedure1

a.

Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




Post-procedure1

a.

Install the air cleaner filter element sub-assembly.

HINT:

Click hereGeneral>MAINTENANCE>M15A-FXE AIR CLEANER FILTER ELEMENT>INSTALLATION



Hide 13750 6.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

Pre-procedure1

a.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



Procedure1

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


Post-procedure1

a.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform the valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 7.INSPECT IGNITION TIMING

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



Pre-procedure1

a.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



b.

Warm up and stop the engine.


c.

Connect the GTS to the DLC3.


d.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



Procedure1

a.

Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.

Powertrain > Engine > Data List
Tester Display
Ignition Timing Cylinder #1
50003 372 213
Standard Ignition Timing:
Condition Specified Condition
Idle speed -7.1 to 29.5°CA BTDC



b.

Check that the ignition timing advances immediately when the engine speed is increased.


c.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.

Powertrain > Engine > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Ignition Timing Cylinder #1
50004 372 22 213

d.

Monitor Ignition Timing Cylinder #1 of the Data List.

Standard Ignition Timing:
Condition Specified Condition
Idle speed 8 to 12°CA BTDC



e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / OFF.


f.

Check that the ignition timing advances immediately when the engine speed is increased.


Post-procedure1

a.

None


Hide 8.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



Pre-procedure1

a.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



b.

Warm up and stop the engine.


c.

Connect the GTS to the DLC3.


d.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



Procedure1

a.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

b.

Read the value displayed on the tester.

Standard Idle Speed:
Condition Specified Condition
P Position 950 to 1050 rpm



Post-procedure1

a.

None


Hide 9.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.


Pre-procedure1

a.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



b.

Warm up and stop the engine.



d.

Remove the 3 spark plugs.

HINT:

Click hereGeneral>MAINTENANCE>M15A-FXE SPARK PLUG>REMOVAL


NOTICE:

DTCs will be stored if the inspection is performed with the ignition coil assembly connectors disconnected. Make sure that the ignition coil assembly connectors are connected during the inspection.



e.

Disconnect the No. 5 engine wire connector.


Procedure1

a.
A461024

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Turn the GTS on.

NOTICE:

Check the HV battery voltage in the Data List to ensure that the battery is fully charged.



v.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Compression Test / ON.

Powertrain > Hybrid Control > Active Test
Tester Display
Compression Test
50004 397 42000

vi.

Depress and hold the brake pedal, and turn the power switch on (READY). Then check the compression pressure.

Standard Compression Pressure:
Item Minimum Compression Pressure Specified Condition
No.1 Cylinder 800 kPa
8.2 kgf/cm2
116 psi
900 kPa
9.2 kgf/cm2
131 psi
No.2 Cylinder 800 kPa
8.2 kgf/cm2
116 psi
900 kPa
9.2 kgf/cm2
131 psi
No.3 Cylinder 800 kPa
8.2 kgf/cm2
116 psi
900 kPa
9.2 kgf/cm2
131 psi
Pressure Difference between Each Cylinder - 0.2 MPa
2.0 kgf/cm2
29 psi


NOTICE:
·

Noise may be emitted from the hybrid vehicle transaxle assembly. However, this is not a malfunction.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




vii.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





Post-procedure1

a.

Connect the No. 5 engine wire connector.


b.

Install the 3 spark plugs.

HINT:

Click hereGeneral>MAINTENANCE>M15A-FXE SPARK PLUG>INSTALLATION



c.

Clear the DTCs.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR


NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 10.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


Pre-procedure1

a.

Put the engine in inspection mode.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


Procedure1

a.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders

5.

Faulty EGR


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire

3.

Faulty EGR


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)


4.

Faulty EGR





Post-procedure1

a.

None