Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AD911  Hybrid/EV Battery Positive Contactor Circuit Short to Ground  


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground Short to ground in the SMRB circuit:
Primary circuit of SMR (+) is malfunctioning.
(2 trip detection logic)
·

Wire harness or connector

·

No. 1 traction battery device box assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P0AD911
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid/EV Battery Voltage

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

SMRP Control Status

·

SMRB Control Status

·

SMRG Control Status

·

Boosting Converter Shutdown Status

·

Generator Inverter Shutdown Status

·

Motor Inverter Shutdown Status



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

If DTC P0AD911 is output, the ignition switch cannot be turned to ON (READY).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

a.
A365589C21
1.542,0.115 2,0.396 0.458,0.281 0.948,1.146 1.344,1.833 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.667,0.188 2.042,0.396 0.375,0.208 10 false H44 1.354,1.875 1.854,2.063 0.5,0.188 10 false SMRB
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-2 (SMRB) - Body ground Ignition switch off 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the H44 hybrid vehicle control ECU connector.



OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458484N01
0.719,0.292 1.104,0.563 0.385,0.271 0.792,0.344 1.073,0.51 0.281,0.167 10 true O70

Disconnect the O70 No. 1 traction battery device box assembly connector.


d.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

a.
A458549C01
1.531,2.573 1.979,2.896 0.448,0.323 1.448,0.156 1.917,0.427 0.469,0.271 1.417,3.583 1.052,4.135 true 0.885,1.188 1.406,1.99 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.573,0.229 1.906,0.406 0.333,0.177 10 false H44 1.635,2.656 1.969,2.833 0.333,0.177 10 false O70 1.406,2.01 2.021,2.208 0.615,0.198 10 false SMRB 0.729,4.156 1.344,4.354 0.615,0.198 10 false SMRB
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44,O70)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

H44-2 (SMRB) or O70-1 (SMRB) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the H44 hybrid vehicle control ECU connector.


b.

Reconnect the O70 No. 1 traction battery device box assembly connector.


c.

Install the HV battery upper cover panel.



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR