Refer to the description for DTC P0AE411.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P0AD915 | Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open | Open or short to +B in the SMRB circuit:
Primary circuit of SMR (+) is malfunctioning. (2 trip detection logic) |
·
Wire harness or connector ·
No. 1 traction battery device box assembly ·
Hybrid vehicle control ECU |
Does not come on | Master Warning: Comes on | Hybrid Control | A |
| DTC No. | Data List |
|---|---|
| P0AD915 | ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting ·
Hybrid/EV Battery Voltage ·
SMRP Status ·
SMRB Status ·
SMRG Status ·
SMRP Control Status ·
SMRB Control Status ·
SMRG Control Status ·
Boosting Converter Shutdown Status ·
Generator Inverter Shutdown Status ·
Motor Inverter Shutdown Status |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY) and wait for 30 seconds or more.
Turn the ignition switch off and wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*
*: for AWD
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.
*: for AWD
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
If DTC P0AD915 is output, the ignition switch cannot be turned to ON (READY).
Pre-procedure1
None.
Procedure1
Read the Data List.
| Tester Display |
|---|
| SMRB Status |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| SMRB Status | Ignition switch ON | OFF |
| Result | Proceed to |
|---|---|
| The value of SMRB Status is OFF | A |
| The value of SMRB Status is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44)Location & Routingewd_type=routing;type=c;code=H44 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2 |
||
| H44-2 (SMRB) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the H44 hybrid vehicle control ECU connector.
Procedure1
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44)Location & Routingewd_type=routing;type=c;code=H44 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2 |
||
| H44-2 (SMRB) - Body ground | Ignition switch off | 19.0 to 59.0 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the H44 hybrid vehicle control ECU connector.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Disconnect the H44 hybrid vehicle control ECU connector.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44,O70)Location & Routingewd_type=routing;type=c,c;code=H44,O70 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=1 |
||
| H44-2 (SMRB) or O70-1 (SMRB) - Body ground | Ignition switch ON | Below 1 V |
Turning the ignition switch to ON with the hybrid vehicle control ECU connector and the No. 1 traction battery device box assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Reconnect the H44 hybrid vehicle control ECU connector.
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Disconnect the H44 hybrid vehicle control ECU connector.
Procedure1
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44,O70)Location & Routingewd_type=routing;type=c,c;code=H44,O70 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=1 |
||
| H44-2 (SMRB) - O70-1 (SMRB) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44,O70)Location & Routingewd_type=routing;type=c,c;code=H44,O70 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=1 |
||
| H44-2 (SMRB) or O70-1 (SMRB) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the H44 hybrid vehicle control ECU connector.
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O70)Location & Routingewd_type=routing;type=c;code=O70 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=3 |
||
| O70-3 (GND) - Body ground | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(No. 1 Traction Battery Device Box Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O70)Location & Routingewd_type=routing;type=c;code=O70 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=1,3 |
||
| O70-1 (SMRB) - O70-3 (GND) | -40 to 80°C (-40 to 176°F) | 19.0 to 59.0 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG