Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441184 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P0E3116  DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Below Threshold  P0E3117  DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Above Threshold  P0E311F  DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent  


DESCRIPTION

The motor generator control ECU, which is built into the hybrid motor control inverter assembly, detects pre-boosting high voltage (VL) using the voltage sensor in the boost converter to control boosting. The motor generator control ECU also monitors the boost converter voltage sensor signal line and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0E3116 DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Below Threshold Boost converter voltage (VL) signal is stuck (Low)
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Hybrid vehicle control ECU

·

Hybrid motor control inverter assembly


Comes on Master Warning:
Comes on
Motor Generator A
P0E3117 DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Above Threshold Boost converter voltage (VL) signal is stuck (High)
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Hybrid vehicle control ECU

·

Hybrid motor control inverter assembly


Comes on Master Warning:
Comes on
Motor Generator A
P0E311F DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent Boost converter voltage (VL) signal is stuck (Low) or (High) detected when DTC P0C7917, P0E5717, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Hybrid vehicle control ECU

·

Hybrid motor control inverter assembly


Does not come on Master Warning:
Does not come on
Motor Generator A

Related Data List
DTC No. Data List
P0E3116
P0E3117
P0E311F
VL Voltage

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
Only P0E3116 for Motor generator control system is output A
P0E3117 and P0E311F are output and DTCs other than the DTCs in the table below are output B
Any Hybrid control system DTCs in the table below are output C
Any Motor generator control system DTCs in the table below are output D


System Relevant Diagnosis
Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Motor generator control system P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message

HINT:

P0E3116, P0E3117 or P0E311F may be stored due to a malfunction which also causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (MOTOR GENERATOR)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

C

D

GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM)

2.CHECK FREEZE FRAME DATA (MOTOR GENERATOR)
a.

Read the freeze frame data of DTC P0E3116.

Powertrain > Motor Generator > DTC(P0E3116) > Freeze Frame Data
Tester Display
VH Voltage
50040 395 111 P0E3116
Result:
Result Proceed to
The value of VH Voltage is less than 55 V A
The value of VH Voltage is 55 V or more B



b.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT

B

3.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397
Powertrain > Motor Generator > Clear DTCs
50002 395
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK DTC OUTPUT (HYBRID CONTROL)
5.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.


Procedure1

a.

Turn the ignition switch to ON (READY).

HINT:
·

If the ignition switch could not be turned to ON (READY), turn the ignition switch off and check for DTCs after turning the ignition switch to ON (READY) again.

·

Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.




b.

Ensure the safety of the areas in front and at the back of the vehicle.


c.

Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.

HINT:

Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.



d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1C8449 is output, or no DTCs are output. A
Ignition switch could not be turned to ON (READY) and DTC P300449 is output. B



Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

NG

CONNECT SECURELY

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



d.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.
A459260C02
2.604,3.333 3.073,3.604 0.469,0.271 1.49,0.188 1.875,0.438 0.385,0.25 1.354,3.573 0.865,4.073 true 0.885,1.146 1.375,1.917 true 0.677,1.417 0.542,1.906 true 2.01,3.583 2.385,4.063 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.573,0.25 1.906,0.427 0.333,0.177 10 false H44 2.729,3.385 3.063,3.563 0.333,0.177 10 false O70 1.24,1.938 1.854,2.135 0.615,0.198 10 false SMRB 0.635,4.104 1.25,4.302 0.615,0.198 10 false SMRB 0.333,1.938 0.948,2.135 0.615,0.198 10 false SMRG 2.26,4.115 2.875,4.313 0.615,0.198 10 false SMRG
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(H44,O70)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

H44-2 (SMRB) - O70-1 (SMRB) Ignition switch off Below 1 Ω P0E3116,P0E3117,P0E311F
H44-27 (SMRG) - O70-4 (SMRG) Ignition switch off Below 1 Ω P0E3116,P0E3117,P0E311F


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.


c.

Reconnect the H44 hybrid vehicle control ECU connector.



OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.
A365602C58
2.667,1.083 3,1.344 0.333,0.26 1.896,1.25 2.292,1.823 false 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 2.719,1.135 3.167,1.333 0.448,0.198 10 false O70
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-3 (GND) - Body ground Ignition switch off Below 1 Ω P0E3116,P0E3117,P0E311F


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.



OK

11.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

12.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
12.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)

Pre-procedure1

a.

Install the service plug grip.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for 2 minutes or more.


e.

Turn the ignition switch to (READY).


Procedure1

a.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227
Result:
Result Proceed to
The difference between the value of Hybrid/EV Battery Voltage and VL-Voltage before Boosting is less than 50 V A
The difference between the value of Hybrid/EV Battery Voltage and VL-Voltage before Boosting is 50 V or more B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B