Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P300449  High Voltage Power Resource Circuit Short during Pre-Charge  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and hybrid motor control inverter assembly and detects an open circuit malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

No. 1 traction battery device box assembly malfunction

·

Hybrid motor control inverter assembly malfunction

·

Rear hybrid motor control inverter assembly (for AWD)

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU malfunction

·

No. 1 traction battery device box assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



INSPECTION DESCRIPTION


A476328E03
0.469,2.479 3.073,2.677 2.604,0.198 10 false Service Plug Grip 0.354,0.531 1.271,0.729 0.917,0.198 10 false *d, *e 2.573,0.521 2.885,0.719 0.313,0.198 10 false *b 0.74,0.302 2.271,0.5 1.531,0.198 10 false HV Battery 2.427,1.115 3.042,1.313 0.615,0.198 10 false SMRB 2.729,2.021 3.344,2.219 0.615,0.198 10 false SMRG 2.729,2.583 3.344,2.781 0.615,0.198 10 false SMRP 1.823,2.563 2.667,3.042 0.844,0.479 10 false System Main Resistor 3.833,0.781 4.146,0.979 0.313,0.198 10 false *c 4.635,2.021 5.667,2.448 1.031,0.427 10 false Boost Converter 5.917,2 6.417,2.385 0.5,0.385 10 false Inverter 1.167,3.438 3.979,3.635 2.813,0.198 10 false No. 1 Traction Battery Device Box Assembly 4.792,3.698 5.104,3.896 0.313,0.198 10 false *a 5.479,3.74 6.323,4.281 0.844,0.542 10 false System main relay signal 4.396,2.917 6.885,3.177 2.49,0.26 10 false Hybrid Motor Control Inverter Assembly 5.271,4.354 7.042,4.781 1.771,0.427 10 false Hybrid Vehicle Control ECU 1.115,4.729 4.021,4.927 2.906,0.198 10 false : High Voltage Line 1.115,5.063 3.865,5.26 2.75,0.198 10 false : Inspection Areas 0.104,0.073 0.885,0.323 0.781,0.25 12 false for 2WD:

A476329E05
0.125,0.073 1.354,0.271 1.229,0.198 12 false for AWD: 0.646,2.583 2.333,2.781 1.688,0.198 10 false Service Plug Grip 1.094,0.552 1.865,0.792 0.771,0.24 10 false HV Battery 2.781,1.313 3.198,1.479 0.417,0.167 10 false SMRB 3.083,2.188 3.5,2.354 0.417,0.167 10 false SMRG 3.094,2.823 3.51,2.99 0.417,0.167 10 false SMRP 2.198,2.792 3.104,3.177 0.906,0.385 10 false System Main Resistor 2.042,6.385 4.635,6.604 2.594,0.219 10 false Hybrid Motor Control Inverter Assembly 2.188,5.51 2.854,5.688 0.667,0.177 10 false Inverter 3.135,5.531 4.125,5.75 0.99,0.219 10 false Boost Converter 1.813,3.542 4.604,3.792 2.792,0.25 10 false No. 1 Traction Battery Device Box Assembly 0.281,4.531 1.771,5.01 1.49,0.479 10 false Hybrid Vehicle Control ECU 0.583,3.792 1.427,4.229 0.844,0.438 10 false System main relay signal 5.448,2.76 7.042,3.167 1.594,0.406 10 false Rear Hybrid Motor Control Inverter Assembly 6.354,2.188 7.021,2.365 0.667,0.177 10 false Inverter 5.396,4.021 5.615,4.229 0.219,0.208 10 false *c 0.729,3.146 0.948,3.354 0.219,0.208 10 false *a 4.188,0.938 4.406,1.146 0.219,0.208 10 false *c 2.917,0.75 3.135,0.958 0.219,0.208 10 false *b 0.552,0.771 1.031,0.979 0.479,0.208 10 false *d, *e 1.167,7.125 2.667,7.365 1.5,0.24 10 false : High Voltage Line 1.167,7.448 3.094,7.646 1.927,0.198 10 false : Inspection Areas

System Diagram Range Inspection Content Reason
*a Check connection condition and wire harness continuity between hybrid vehicle control ECU and No. 1 traction battery device box assembly Check whether connectors are connected properly and check for an open circuit in the SMRP and SMRB primary lines
*b Check system main relay Check whether SMRB and SMRP stuck OFF
*c Check connection condition and high-voltage cable continuity between No. 1 traction battery device box assembly and hybrid motor control inverter assembly or rear hybrid motor control inverter assembly Check for open circuit and defective connection (arc marks) due to looseness
*d Check high-voltage cable and connection condition between HV battery and No. 1 traction battery device box assembly Check for open circuit and defective connection (arc marks) due to looseness
*e Check HV battery Check whether HV battery voltage has drastically dropped below normal range


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and the hybrid motor control inverter assembly and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P300449 High Voltage Power Resource Circuit Short during Pre-Charge Although a system main relay operation signal was sent when the ignition switch was operated, the system voltage is not sufficiently increased after boosting and the HV battery current does not flow.
High-voltage circuit malfunctions between the HV battery and hybrid motor control inverter assembly.
The EV electric battery fuse is blown, the service plug grip is removed, the system main resistor is blown, SMRP or SMRB remains open, or the high-voltage cable has an open circuit.
(2 trip detection logic)
·

No. 1 traction battery device box assembly

·

HV floor under wire

·

Hybrid motor control inverter assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Electric vehicle battery plug assembly

·

Wire harness or connector

·

Rear hybrid motor control inverter assembly*

·

Hybrid battery pack wire*


Does not come on Master Warning: Comes on Hybrid Control A

*: for AWD

Related Data List
DTC No. Data List
P300449
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal

·

Inter Lock Switch

·

SMRP Status

·

SMRB Status

·

SMRG Status


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.


·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.


·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P300449 and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P300449 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output B
P300449 and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output C
P300449 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output D
P300449 and Communication system malfunction of Hybrid control system DTCs in the table below are output E
P300449 and Sensor and actuator circuit malfunction of Hybrid control system DTCs in the table below are output F
P300449 and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output G
P300449 and System malfunction of Hybrid control system DTCs in the table below are output H
P300449 and System malfunction of Motor generator control system DTCs in the table below are output I
P300449 and DTCs other than the DTCs in the table below are output J
Only P300449 for Hybrid control system is output K


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short
P1C8249 High Voltage Power Resource Circuit Over Loading
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P0CA300 DC/DC Converter Step Up Voltage Performance

HINT:
·

P300449 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

C

D

E

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

F

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

G

H

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

I

J

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

K

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P300449.

Powertrain > Hybrid Control > DTC(P300449) > Freeze Frame Data
Tester Display
VH-Voltage after Boosting
50040 397 151 P300449
Result:
Result Proceed to
Both of the following conditions are met:
·

"VH-Voltage after Boosting" is below 50 V.

·

Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 35 V or less.


A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P300449.

Powertrain > Hybrid Control > DTC(P300449) > Freeze Frame Data
Tester Display
VH-Voltage after Boosting
Hybrid/EV Battery Voltage
50040 397 151,227 P300449
Result:
Result Proceed to
The difference between the value of Hybrid/EV Battery Voltage and VH-Voltage after Boosting is 35 or less A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


d.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

a.
A458549C07
1.531,2.604 2,2.875 0.469,0.271 1.469,0.167 1.938,0.438 0.469,0.271 1.427,3.573 0.813,4.083 true 1.135,1.313 1.865,1.958 true 0.896,1.177 0.49,1.938 true 1.656,3.594 1.677,4.115 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.594,0.24 1.927,0.417 0.333,0.177 10 false H44 1.656,2.667 1.99,2.844 0.333,0.177 10 false O70 0.24,1.99 0.854,2.188 0.615,0.198 10 false SMRB 0.635,4.125 1.25,4.323 0.615,0.198 10 false SMRB 1.875,1.979 2.49,2.177 0.615,0.198 10 false SMRP 1.521,4.146 2.135,4.344 0.615,0.198 10 false SMRP
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44,O70)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

H44-2 (SMRB) - O70-1 (SMRB) Ignition switch off Below 1 Ω
H44-16 (SMRP) - O70-2 (SMRP) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the H44 hybrid vehicle control ECU connector.


b.

Reconnect the O70 No. 1 traction battery device box assembly connector.


c.

Install the HV battery upper cover panel.



OK

8.CHECK VEHICLE CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

9.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

B

26.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.
A436194C15
1.5,0.271 1.906,0.573 0.406,0.302 1.823,1.229 2.292,1.823 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 1.594,0.365 1.948,0.604 0.354,0.24 10 false O70
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-3 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.



OK

10.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C07
3.771,1.031 4.125,1.281 0.354,0.25 3.26,0.094 3.625,0.344 0.365,0.25 6.219,0.698 6.615,0.917 0.396,0.219 3.156,1.51 3.417,1.26 true 3.771,1.49 3.604,1.271 true 3.448,0.719 3.917,0.26 true 6.313,1.198 5.813,0.802 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.844,1.094 4.302,1.292 0.458,0.198 10 false O70 2.906,1.542 3.24,1.75 0.333,0.208 10 true GND 3.781,1.521 4.24,1.719 0.458,0.198 10 true SMRB 6.323,0.74 6.583,0.885 0.26,0.146 10 true z10 3.979,0.177 4.438,0.375 0.458,0.198 10 false CBI 3.385,0.135 3.594,0.302 0.208,0.167 10 true a1 6.406,1.198 6.563,1.396 0.156,0.198 10 false +
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z10,a1)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

z10-1 (+) - a1-1 (CBI) Auxiliary battery voltage applied between terminals O70-1 (SMRB) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-1 (SMRB) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

11.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

11.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C08
3.76,1.031 4.125,1.271 0.365,0.24 2.271,0.094 2.635,0.333 0.365,0.24 1.177,0.094 1.542,0.333 0.365,0.24 3.208,1.51 3.438,1.26 true 3.729,1.521 3.521,1.26 true 2.125,1.167 2.458,0.781 true 0.865,0.917 1.375,0.719 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.833,1.094 4.292,1.292 0.458,0.198 10 false O70 2.958,1.552 3.292,1.76 0.333,0.208 10 true GND 3.729,1.531 4.188,1.74 0.458,0.208 10 true SMRP 1.302,0.146 1.49,0.313 0.188,0.167 10 true z9 2.385,0.135 2.583,0.302 0.198,0.167 10 true a2 1.885,1.146 2.26,1.354 0.375,0.208 10 false CEI 0.74,0.885 0.896,1.083 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9,a2)Location & Routing

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(a2)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

z9-1 (-) - a2-1 (CEI) Auxiliary battery voltage applied between terminals O70-2 (SMRP) and O70-3 (GND) 24.3 to 29.7 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-2 (SMRP) -O70-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

12.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

12.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A475642

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the HV floor under wire from the hybrid motor control inverter assembly.


c.

Check for arc marks on the terminals for the HV floor under wire and hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire.



A

13.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458497N02
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true a1 2.177,1.5 2.365,1.677 0.188,0.177 10 true a2

Check that the HV floor under wire is connected securely, and there are no contact problems.


b.

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


c.

Check for arc marks on the terminals of the HV floor under wire and the No. 1 traction battery device box assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire connectors.


b.

Install the HV battery upper cover panel.



A

14.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

14.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N02
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true a1 2.177,1.5 2.365,1.677 0.188,0.177 10 true a2

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.
A475630

Disconnect the HV floor under wire connector from the hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A409066C30
1.875,0.875 2.271,1.115 0.396,0.24 3.74,0.531 4.135,0.771 0.396,0.24 5.625,0.531 6.021,0.771 0.396,0.24 1.281,1.958 1.917,1.677 true 3.948,1.146 4.333,0.708 true 5.771,1.073 5.396,0.708 true 2.781,1.865 2.208,1.677 true 1.281,1.24 1.594,1.24 true 6.26,2.365 6.573,2.365 true 0.594,0.5 0.906,0.656 0.313,0.156 10 false *a 3.594,0.208 3.906,0.365 0.313,0.156 10 false *b 2,0.938 2.313,1.135 0.313,0.198 10 false a3 3.865,0.573 4.177,0.771 0.313,0.198 10 false a1 5.76,0.583 6.073,0.781 0.313,0.198 10 false a2 1.021,1.906 1.479,2.104 0.458,0.198 10 false CBI 3.677,1.083 4.135,1.281 0.458,0.198 10 false CBI 5.823,1.021 6.281,1.219 0.458,0.198 10 false CEI 2.844,1.781 3.302,1.979 0.458,0.198 10 false CEI 1.115,1.188 1.427,1.344 0.313,0.156 10 false *1 6.646,2.313 6.958,2.469 0.313,0.156 10 false *1
*1 Shield Ground - -
*a HV Floor Under Wire
(Hybrid Motor Control Inverter Assembly Side)
*b HV Floor Under Wire
(No. 1 Traction Battery Device Box Assembly Side)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(a3,a1,a2)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

Click Connector(a2)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

a3-1 (CBI) - a1-1 (CBI) Ignition switch off Below 1 Ω
a3-2 (CEI) - a2-1 (CEI) Ignition switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV floor under wire connectors.


b.

Install the HV battery upper cover panel.



OK

15.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

15.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458506N01
2.885,0.156 3.208,0.406 0.323,0.25 1.969,1.708 2.292,1.958 0.323,0.25 2.969,0.208 3.167,0.375 0.198,0.167 10 true z9 2.021,1.76 2.271,1.927 0.25,0.167 10 true z10

Check the HV battery high voltage connector and electric vehicle battery plug connector securely, and there are no contact problems.


b.

Disconnect the HV battery high voltage connector and electric vehicle battery plug connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



c.

Check for arc marks on the terminals of the HV battery high voltage connectors and No. 1 traction battery device box assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV battery high voltage connector and electric vehicle battery plug connector.


b.

Install the HV battery upper cover panel.



A

16.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458507N01
0.083,0.75 0.448,0.979 0.365,0.229 0.583,0.073 0.948,0.302 0.365,0.229 0.188,0.792 0.396,0.948 0.208,0.156 10 true z8 0.656,0.125 0.917,0.281 0.26,0.156 10 true z14

Check the HV battery high voltage connector and electric vehicle battery plug connector securely, and there are no contact problems.


b.

Disconnect the HV battery high voltage connector and electric vehicle battery plug connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



c.

Check for arc marks on the terminals of the HV battery high voltage connectors and hybrid battery terminal block.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV battery high voltage connector and electric vehicle battery plug connector.


b.

Install the HV battery upper cover panel.



A

17.CHECK HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

17.CHECK HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.
A475594N02
0.906,1.01 1.25,1.26 0.344,0.25 1.042,1.063 1.188,1.229 0.146,0.167 10 true A

Check that the HV battery high voltage connector is connected securely, and there are no contact problems.


b.

Disconnect the HV battery high voltage connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



c.

Check for arc marks on the terminals of the HV battery high voltage connector.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Connect the HV battery high voltage connector.


b.

Install the upper No. 1 hybrid battery cover sub-assembly.



A

18.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

18.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458508N01
0.344,1.177 0.677,1.417 0.333,0.24 1.677,0.719 2.042,0.958 0.365,0.24 0.417,1.208 0.604,1.385 0.188,0.177 10 true z8 1.75,0.75 1.969,0.927 0.219,0.177 10 true z9

Disconnect the 2 electric vehicle battery plug assembly connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A451764C02
0.396,1.021 0.75,1.292 0.354,0.271 0.854,2.854 1.208,3.125 0.354,0.271 5.344,1.979 4.823,2.583 true 5.573,1.99 6.094,2.583 true 1.594,1.219 1.76,1.74 true 0.698,0.396 1.01,0.552 0.313,0.156 10 false *a 0.708,2.177 1.021,2.333 0.313,0.156 10 false *b 3.948,1.063 4.26,1.219 0.313,0.156 10 true *c 4.76,2.604 4.948,2.771 0.188,0.167 10 true 1 6.063,2.615 6.25,2.781 0.188,0.167 10 true 2 0.51,1.094 0.792,1.323 0.281,0.229 10 false z9 0.969,2.917 1.354,3.208 0.385,0.292 10 false z8 1.781,1.781 2.094,1.938 0.313,0.156 10 false -
*a Electric Vehicle Battery Plug Assembly Connector
(No. 1 Traction Battery Device Box Assembly Side)
*b Electric Vehicle Battery Plug Assembly Connector
(Hybrid Battery Terminal Block Side)
*c Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z8,z9)Location & Routing

Click Connector(z8)Body>other>Hybrid Battery Terminal Block , HV Supply Battery Assembly

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z8-1 - Service plug grip connecting terminal 1 Ignition switch off Below 1 Ω
z9-1 (-) - Service plug grip connecting terminal 2 Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the 2 electric vehicle battery plug assembly connectors.


b.

Install the HV battery upper cover panel.



OK

19.CHECK HYBRID BATTERY TERMINAL BLOCK

NG

REPLACE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

19.CHECK HYBRID BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458507N01
0.083,0.75 0.448,0.979 0.365,0.229 0.583,0.073 0.948,0.302 0.365,0.229 0.188,0.792 0.396,0.948 0.208,0.156 10 true z8 0.656,0.125 0.917,0.281 0.26,0.156 10 true z14

Disconnect the HV battery high voltage connector and electric vehicle battery plug assembly connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A458510C01
0.906,0.938 1.26,1.167 0.354,0.229 1.479,0.458 1.833,0.688 0.354,0.229 0.052,0.052 0.271,0.219 0.219,0.167 10 true *a 1.021,0.979 1.208,1.135 0.188,0.156 10 true z8 1.542,0.5 1.813,0.667 0.271,0.167 10 true z14
*a Component without harness connected
(Hybrid Battery Terminal Block)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z8,z14)Location & Routing

Click Connector(z8)Body>other>Hybrid Battery Terminal Block , HV Supply Battery Assembly

Click Connector(z14)Body>other>Hybrid Battery Terminal Block , HV Supply Battery Assembly

z8-1 - z14-1 Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV battery high voltage connector and electric vehicle battery plug assembly connector.


b.

Install the HV battery upper cover panel.



OK

20.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK

20.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458512N01
1.906,1.635 2.292,1.854 0.385,0.219 1.979,1.677 2.25,1.833 0.271,0.156 10 true z10

Disconnect the No. 2 HV supply stack sub-assembly connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
A475594N02
0.906,1.01 1.25,1.26 0.344,0.25 1.042,1.063 1.188,1.229 0.146,0.167 10 true A

Disconnect the No. 2 HV supply stack sub-assembly connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A460000C01
0.844,0.281 1.219,0.552 0.375,0.271 0.417,3.125 0.792,3.396 0.375,0.271 1.344,1.896 1.229,1.344 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 0.24,2.479 0.552,2.635 0.313,0.156 10 false *b 0.927,0.333 1.24,0.49 0.313,0.156 10 false z10 0.573,3.198 0.885,3.354 0.313,0.156 10 false A 1.375,1.927 1.698,2.135 0.323,0.208 10 false +
*a No. 2 HV Supply Stack Sub-assembly Connector
(to Hybrid Battery Terminal Block)
*b No. 2 HV Supply Stack Sub-assembly Connector
(to No. 1 HV Supply Stack Sub-assembly Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z10-1 (+) - A-1 Ignition switch off 50 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 2 HV supply stack sub-assembly connectors.


b.

Install the upper No. 1 hybrid battery cover sub-assembly.



OK

21.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

21.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.

Remove the electric vehicle battery plug assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY PLUG>REMOVAL



d.
A458511N01
0.26,0.677 0.625,0.927 0.365,0.25 0.333,0.729 0.615,0.885 0.281,0.156 10 true z14

Disconnect the No. 1 HV supply stack sub-assembly connector from the No. 1 traction battery device box assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



e.
A475594N02
0.906,1.01 1.25,1.26 0.344,0.25 1.042,1.063 1.188,1.229 0.146,0.167 10 true A

Disconnect the No. 1 HV supply stack sub-assembly connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A460001C01
0.51,1.156 0.948,1.448 0.438,0.292 0.323,3.219 0.76,3.51 0.438,0.292 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a 0.208,2.448 0.521,2.604 0.313,0.156 10 false *b 0.521,3.292 0.979,3.49 0.458,0.198 10 false A 0.635,1.229 1.094,1.427 0.458,0.198 10 false z14
*a No. 1 HV Supply Stack Sub-assembly Connector
(to No. 1 Traction Battery Device Box Assembly)
*b No. 1 HV Supply Stack Sub-assembly Connector
(to No. 2 HV Supply Stack Sub-assembly Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z14)Location & Routing

Click Connector(z14)Body>other>Hybrid Battery Terminal Block , HV Supply Battery Assembly

z14-1 - A-1 Ignition switch off 50 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 2 HV supply stack sub-assembly connectors.


b.

Install the electric vehicle battery plug assembly.


c.

Install the upper No. 1 hybrid battery cover sub-assembly.



OK

22.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

22.CHECK FOR INTERMITTENT PROBLEMS

Result:
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B


HINT:
·

Since 2 trip detection logic is used, the DTC detection condition must be met twice.

·

If DTC P300449 is output again after performing the inspection, replace the hybrid motor control inverter assembly. If DTC P300449 is not output again, replace the No. 1 traction battery device box assembly.




A

23.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

23.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

24.CLEAR DTC
24.CLEAR DTC

NEXT

25.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
25.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. B



A

END

B

26.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.
A436194C15
1.5,0.271 1.906,0.573 0.406,0.302 1.823,1.229 2.292,1.823 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 1.594,0.365 1.948,0.604 0.354,0.24 10 false O70
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-3 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.



OK

27.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C09
3.792,1.031 4.156,1.26 0.365,0.229 3.26,0.094 3.625,0.344 0.365,0.25 6.219,0.698 6.615,0.917 0.396,0.219 3.156,1.51 3.417,1.26 true 3.771,1.49 3.604,1.271 true 3.448,0.719 3.917,0.26 true 6.313,1.198 5.813,0.802 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.865,1.083 4.323,1.281 0.458,0.198 10 false O70 2.906,1.542 3.24,1.75 0.333,0.208 10 true GND 3.781,1.521 4.24,1.719 0.458,0.198 10 true SMRB 6.323,0.74 6.583,0.885 0.26,0.146 10 true z10 3.979,0.177 4.438,0.375 0.458,0.198 10 false CBI 3.385,0.135 3.594,0.302 0.208,0.167 10 true c1 6.406,1.198 6.563,1.396 0.156,0.198 10 false +
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z10,c1)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

z10-1 (+) - c1-1 (CBI) Auxiliary battery voltage applied between terminals O70-1 (SMRB) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-1 (SMRB) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

28.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

28.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C10
3.76,1.031 4.125,1.271 0.365,0.24 2.271,0.094 2.635,0.333 0.365,0.24 1.177,0.094 1.542,0.333 0.365,0.24 3.208,1.51 3.438,1.26 true 3.729,1.521 3.521,1.26 true 2.125,1.167 2.458,0.781 true 0.865,0.917 1.375,0.719 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.823,1.083 4.281,1.281 0.458,0.198 10 false O70 2.958,1.552 3.292,1.76 0.333,0.208 10 true GND 3.729,1.531 4.188,1.74 0.458,0.208 10 true SMRP 1.302,0.146 1.49,0.313 0.188,0.167 10 true z9 2.385,0.135 2.583,0.302 0.198,0.167 10 true c2 1.885,1.146 2.26,1.354 0.375,0.208 10 false CEI 0.74,0.885 0.896,1.083 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9,c2)Location & Routing

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

z9-1 (-) - c2-1 (CEI) Auxiliary battery voltage applied between terminals O70-2 (SMRP) and O70-3 (GND) 24.3 to 29.7 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-2 (SMRP) -O70-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

29.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

29.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A475642

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the HV floor under wire from the hybrid motor control inverter assembly.


c.

Check for arc marks on the terminals for the HV floor under wire and hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire.



A

30.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

30.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


c.
A458569N01
1.604,0.198 2.021,0.49 0.417,0.292 1.74,0.281 1.969,0.458 0.229,0.177 10 true a4

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)



d.

Disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.


Procedure1

a.

Check for arc marks on the terminals for the HV floor under wire and rear hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



A

31.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV BATTERY PACK WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

31.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV BATTERY PACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove inverter terminal cover from the rear hybrid motor control inverter assembly.


Procedure1

a.
A475624N01
2.354,0.375 2.729,0.667 0.375,0.292 2.469,0.448 2.656,0.615 0.188,0.167 10 true c6

Check that the bolts for the HV battery pack wire is tightened to the specified torque, the HV battery pack wire is connected securely, and there are no contact problems.

Specified Condition:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


c.

Check for arc marks on the terminals for the HV battery pack wire and rear hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV battery pack wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



A

32.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY PACK WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

32.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY PACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458497N03
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true c1 2.177,1.5 2.365,1.677 0.188,0.177 10 true c2

Check that the HV battery pack wire is connected securely, and there are no contact problems.


b.

Disconnect the HV battery pack wire connectors from the No. 1 traction battery device box assembly.


c.

Check for arc marks on the terminals of the HV battery pack wire and the No. 1 traction battery device box assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV battery pack wire.


b.

Install the HV battery upper cover panel.



A

33.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

33.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N03
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true c1 2.177,1.5 2.365,1.677 0.188,0.177 10 true c2

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.
A475630

Disconnect the HV floor under wire connector from the hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A378816C36
1.844,0.781 2.24,1.052 0.396,0.271 3.708,0.51 4.104,0.781 0.396,0.271 5.625,0.51 6.021,0.781 0.396,0.271 4.396,0.698 4.073,1.094 true 5.333,0.708 5.708,1.115 true 1.906,1.635 1.26,2.042 true 2.229,1.635 2.771,2.042 true 0.865,0.583 1.177,0.74 0.313,0.156 10 false *a 3.708,0.167 4.021,0.323 0.313,0.156 10 false *b 1.979,0.844 2.292,1 0.313,0.156 10 false a3 3.854,0.583 4.167,0.74 0.313,0.156 10 false c1 5.75,0.573 6.063,0.729 0.313,0.156 10 false c2 3.813,1.042 4.125,1.198 0.313,0.156 10 false CBI 5.76,1.073 6.073,1.229 0.313,0.156 10 false CEI 0.979,1.99 1.292,2.146 0.313,0.156 10 false CBI 2.875,1.979 3.188,2.135 0.313,0.156 10 false CEI
*a HV Floor Under Wire
(Hybrid Motor Control Inverter Assembly Side)
*b HV Floor Under Wire
(No. 1 Traction Battery Device Box Assembly Side)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(a3,c1,c2)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

a3-1 (CBI) - c1-1 (CBI) Ignition switch off Below 1 Ω
a3-2 (CEI) - c2-1 (CEI) Ignition switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV floor under wire connector to the hybrid motor control inverter assembly.


b.

Reconnect the HV floor under wire connectors to the No. 1 traction battery device box assembly.


c.

Install the HV battery upper cover panel.



OK

15.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

34.CHECK FLOOR UNDER WIRE
34.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475630

Disconnect the HV floor under wire connector from the hybrid motor control inverter assembly.


c.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


d.
A475646N02
1.604,0.198 2.021,0.49 0.417,0.292 1.74,0.281 1.969,0.458 0.229,0.177 10 true a4

Disconnect HV floor under wire connector from the rear hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A378818C15
1.906,0.844 2.24,1.083 0.333,0.24 5.073,0.969 5.406,1.208 0.333,0.24 1.896,1.656 1.208,2.354 true 2.208,1.667 2.844,2.344 true 5.01,2.073 4.469,2.844 true 5.438,2.073 5.969,2.823 true 0.781,0.74 1.094,0.896 0.313,0.156 10 false *a 4.115,0.771 4.427,0.927 0.313,0.156 10 false *b 1.094,2.385 1.479,2.604 0.385,0.219 10 false CBI 2.802,2.375 3.188,2.594 0.385,0.219 10 false CEI 2.01,0.896 2.396,1.115 0.385,0.219 10 false a3 5.177,1.01 5.563,1.229 0.385,0.219 10 false a4 4.24,2.865 4.75,3.115 0.51,0.25 10 false RCEO 5.865,2.875 6.375,3.125 0.51,0.25 10 false RCBO
*1 Shield Ground - -
*a HV Floor Under Wire
(Hybrid Motor Control Inverter Assembly Side)
*b HV Floor Under Wire
(Rear Hybrid Motor Control Inverter Assembly Side)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(a3,a4)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a4)Body>HV Floor Under Wire>Rear Hybrid Motor Control Inverter Assembly

a3-1 (CBI) - a4-2 (RCBO) Ignition switch off Below 1 Ω
a3-2 (CEI) - a4-1 (RCEO) Ignition switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV floor under wire connector to the hybrid motor control inverter assembly.


b.

Install the inverter terminal cover to the rear hybrid motor control inverter assembly.


c.

Reconnect HV floor under wire connector from the rear hybrid motor control inverter assembly.



OK

35.CHECK HV BATTERY PACK WIRE

NG

35.CHECK HV BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N03
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true c1 2.177,1.5 2.365,1.677 0.188,0.177 10 true c2

Disconnect the HV battery pack wire connectors from the No. 1 traction battery device box assembly.


d.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


e.
A475624N01
2.354,0.375 2.729,0.667 0.375,0.292 2.469,0.448 2.656,0.615 0.188,0.167 10 true c6

Disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A378817C17
1.74,1.031 2.083,1.271 0.344,0.24 3.802,0.521 4.146,0.76 0.344,0.24 5.604,0.531 5.948,0.771 0.344,0.24 1.667,2.042 1.156,2.729 true 2.115,2.042 2.615,2.74 true 4.396,0.698 3.958,1.177 true 5.333,0.698 5.76,1.167 true 0.802,0.552 1.115,0.708 0.313,0.156 10 false *a 3.552,0.177 3.865,0.333 0.313,0.156 10 false *b 0.979,2.75 1.5,2.938 0.521,0.188 10 false RCBI 2.5,2.76 3.021,2.948 0.521,0.188 10 false RCEI 3.792,1.198 4.313,1.385 0.521,0.188 10 false CBI 5.75,1.198 6.271,1.385 0.521,0.188 10 false CEI 3.917,0.563 4.24,0.729 0.323,0.167 10 false c1 5.719,0.573 6.042,0.74 0.323,0.167 10 false c2 1.844,1.073 2.167,1.24 0.323,0.167 10 false c6
*1 Shield Ground - -
*a HV Battery Pack Wire
(Rear Hybrid Motor Control Inverter Assembly Side)
*b HV Battery Pack Wire
(Hybrid Battery Junction Clock Assembly Side)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(c6,c1,c2)Location & Routing

Click Connector(c6)Body>HV Battey Pack Wire>Rear Hybrid Motor Control Inverter Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

c6-1 (RCBI) - c1-1 (CBI) Ignition switch off Below 1 Ω
c6-2 (RCEI) - c2-1 (CEI) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV battery pack wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.


c.

Reconnect the HV battery pack wire to the No. 1 traction battery device box assembly.


d.

Install the HV battery upper cover panel.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG