Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0ABF28  Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

Refer to the description for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure The offset value of the battery current sensor is excessively large.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
HV Battery A

Related Data List
DTC No. Data List
P0ABF28 Hybrid/EV Battery Current

HINT:
·

Make sure to perform Current Sensor Offset Learning after replacing a battery current sensor.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0C3000

·

This DTC may be output if Current Sensor Offset Learning has not been completed.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Drive the vehicle on urban roads for approximately 10 minutes.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch ON and wait for 10 seconds or more.

6.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

7.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF11

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0ABF28 for Hybrid battery system is output A
P0ABF28 and DTCs other than the DTCs in the table below are output B
P0ABF28 and Hybrid battery system DTCs in the table below are output C
P0ABF28 and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P062F46 Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459831C01
0.094,1.177 0.51,1.458 0.417,0.281 0.146,3.542 0.563,3.823 0.417,0.281 0.823,2.521 1.771,1.625 true 2.573,2.552 1.875,1.635 true 1.219,2.51 1.76,1.729 true 1.938,2.542 1.771,1.854 true 2.458,4.24 1.823,3.885 true 1.594,3.604 0.958,3.25 true 1.594,3.885 0.969,4.167 true 2.469,3.333 1.844,3.615 true 1.135,2.573 1.594,2.771 0.458,0.198 10 false IB0 1.854,2.604 2.313,2.802 0.458,0.198 10 false VIB 2.51,2.604 2.969,2.802 0.458,0.198 10 false IB1 0.708,2.563 1.167,2.76 0.458,0.198 10 false GIB 0.198,1.26 0.656,1.458 0.458,0.198 10 false z12 0.729,3.177 1.188,3.375 0.458,0.198 10 false VIB 0.729,4.135 1.188,4.333 0.458,0.198 10 false GIB 2.531,3.25 2.99,3.448 0.458,0.198 10 false IB1 2.552,4.219 3.01,4.417 0.458,0.198 10 false IB0 0.25,3.604 0.708,3.802 0.458,0.198 10 false z11 0.094,0.167 0.406,0.365 0.313,0.198 10 false *a 0.177,2.927 0.49,3.125 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(z12,z11)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z12-8 (IB1) - z11-2 (IB1) Ignition switch off Below 1 Ω
z12-7 (GIB) - z11-3 (GIB) Ignition switch off Below 1 Ω
z12-19 (IB0) - z11-4 (IB0) Ignition switch off Below 1 Ω
z12-31 (VIB) - z11-1 (VIB) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(z12,z11)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z12-8 (IB1) or z11-2 (IB1) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-7 (GIB) or z11-3 (GIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-19 (IB0) or z11-4 (IB0) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-31 (VIB) or z11-1 (VIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


b.

Reconnect the z12 battery ECU assembly connector.


c.

Install the No. 1 HV battery hose.



OK

3.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR (IB0))

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

3.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A460457C01
0.281,3.271 0.708,3.635 0.427,0.365 1.885,3.438 2.302,3.021 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 2.365,2.938 2.823,3.135 0.458,0.198 10 false VIB 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-1 (VIB) - z11-3 (GIB) Ignition switch ON

NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




b.
A460457C03
0.281,3.271 0.708,3.635 0.427,0.365 1.146,4.083 1.563,3.667 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.927,4.042 1.385,4.24 0.458,0.198 10 false IB0 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Tester Connection

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-4 (IB0) - z11-3 (GIB) Ignition switch ON

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



c.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - 0.514 X VIB Voltage = less than 0.060 V
IB0 voltage - 0.514 X VIB Voltage = -0.060 V or higher

Result:
Result Proceed to
Within the specified range above A
Other than above B



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the HV battery upper cover panel.



A

4.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR (IB1))

B

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

4.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR (IB1))
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A460457C01
0.281,3.271 0.708,3.635 0.427,0.365 1.885,3.438 2.302,3.021 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 2.365,2.938 2.823,3.135 0.458,0.198 10 false VIB 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-1 (VIB) - z11-3 (GIB) Ignition switch ON

NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




b.
A460457C02
0.281,3.271 0.708,3.635 0.427,0.365 1.896,3.667 2.323,4.042 true 1.125,3.073 1.552,3.448 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.917,2.99 1.375,3.188 0.458,0.198 10 false IB1 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 4 V, measure the IB1 voltage according to the value(s) in the table below.

Tester Connection Tester Connection

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-2 (IB1) - z11-3 (GIB) Ignition switch ON

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



c.

Compare the measured values of the IB1 terminal voltage and VIB terminal voltage using the following formula:

Condition
IB1 voltage - 0.486 X VIB Voltage = less than 0.060 V
IB1 voltage - 0.486 X VIB Voltage = -0.060 V or higher

Result:
Result Proceed to
Within the specified range above. A
Other than above B



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the HV battery upper cover panel.



A

5.REPLACE BATTERY ECU ASSEMBLY

B

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

5.REPLACE BATTERY ECU ASSEMBLY

NEXT

6.SIMULATION TEST
6.SIMULATION TEST

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

Procedure1

a.

Drive the vehicle on urban roads for approximately 10 minutes.


b.

Turn the ignition switch off and wait for 2 minutes or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.

Result:
Proceed to
NEXT



Post-procedure1

a.

None.



NEXT

7.CHECK DTC OUTPUT (HV BATTERY)
7.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs are not output A
P0ABF28 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY