Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AAC11  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground  P0AAC15  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensors (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11). The battery ECU assembly uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0AAC11 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground The inlet air temperature sensor output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
HV Battery A
P0AAC15 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The inlet air temperature sensor output voltage is higher than the standard value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
HV Battery A

HINT:

After checking for the above DTCs, check the hybrid system Data List item "Hybrid/EV Battery Cooling Fan Intake Air Temperature 1" using the GTS.

Displayed Temperature Malfunction
-45°C (-49°F) or less Open or +B short circuit
95°C (203°F) or more GND short


Related Data List
DTC No. Data List
P0AAC11 Hybrid/EV Battery Cooling Fan Intake Air Temperature 1
P0AAC15

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A459770E03
3.156,1.323 3.615,1.521 0.458,0.198 10 false VIB 1.75,0.75 3.427,1.042 1.677,0.292 10 false Battery Current Sensor 3.49,1.323 3.948,1.656 0.458,0.333 10 false 1 3.167,1.688 3.625,1.885 0.458,0.198 10 false IB0 3.49,1.688 3.948,2.021 0.458,0.333 10 false 4 3.177,2.063 3.635,2.469 0.458,0.406 10 false IB1 3.49,2.063 3.948,2.396 0.458,0.333 10 false 2 3.156,2.406 3.615,2.813 0.458,0.406 10 false GIB 3.5,2.406 3.958,2.74 0.458,0.333 10 false 3 0.635,2.938 3.646,3.323 3.01,0.385 10 false No. 1 Traction Battery Device Box Assembly 5.5,1.323 5.958,1.521 0.458,0.198 10 false VIB 5.49,1.688 5.948,1.885 0.458,0.198 10 false IB0 5.49,2.073 5.948,2.479 0.458,0.406 10 false IB1 5.479,2.406 5.938,2.813 0.458,0.406 10 false GIB 5.24,1.333 5.698,1.667 0.458,0.333 10 false 31 5.24,1.688 5.698,2.021 0.458,0.333 10 false 19 5.302,2.073 5.76,2.406 0.458,0.333 10 false 8 5.313,2.406 5.771,2.74 0.458,0.333 10 false 7 5.135,5.083 7.01,5.385 1.875,0.302 10 false z12 Battery ECU Assembly 1.427,4.167 3.635,4.479 2.208,0.313 10 false Inlet Air Temperature Sensor 0.938,4.938 4.01,5.344 3.073,0.406 10 false No. 2 HV Supply Stack Sub-assembly 5.51,3.885 5.969,4.292 0.458,0.406 10 false TC0 5.5,4.292 5.958,4.698 0.458,0.406 10 false GC0 5.302,3.885 5.76,4.292 0.458,0.406 10 false 5 5.313,4.292 5.771,4.698 0.458,0.406 10 false 6 0.25,2.938 0.708,3.344 0.458,0.406 10 false z11

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0AAC11 or P0AAC15 for Hybrid battery system is output A
P0AAC11 or P0AAC15 is output and DTCs other than the DTCs in the table below are output B
P0AAC11 or P0AAC15 is output and Hybrid battery system DTCs in the table below are output C
P0AAC11 or P0AAC15 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Check the connections of the z12 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 HV battery hose.



OK

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR

NG

CONNECT SECURELY

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458608

Visually check the installation condition of the inlet air temperature sensor.

Result:
Result Proceed to
The inlet air temperature sensor is installed in the correct location and its claws are engaged securely. A
The claws of the inlet air temperature sensor are damaged. B
The inlet air temperature sensor is not installed correctly, but its claws are not damaged. C



Post-procedure1

a.

Install the HV battery upper cover panel.



A

4.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)

B

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

C

INSTALL PARTS CORRECTLY

4.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C05
1.49,0.115 1.948,0.427 0.458,0.313 1.302,2.865 1.552,2 true 1.969,2.875 1.667,2 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 1.167,2.917 1.604,3.115 0.438,0.198 10 false TC0 1.875,2.917 2.313,3.115 0.438,0.198 10 false GC0
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-5 (TC0) - z12-6 (GC0) Ignition switch off
0 to 10°C (32 to 50°F)
17.7 to 27.8 kΩ
z12-5 (TC0) - z12-6 (GC0) Ignition switch off
10 to 20°C (50 to 68°F)
12.0 to 18.2 kΩ
z12-5 (TC0) - z12-6 (GC0) Ignition switch off
20 to 30°C (68 to 86°F)
8.22 to 12.2 kΩ
z12-5 (TC0) - z12-6 (GC0) Ignition switch off
30 to 40°C (86 to 104°F)
5.74 to 8.41 kΩ
z12-5 (TC0) - z12-6 (GC0) Ignition switch off
40 to 50°C (104 to 122°F)
4.09 to 5.91 kΩ


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z12 battery ECU assembly connectors.


b.

Install the No. 1 HV battery hose.



OK

5.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

5.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C05
1.49,0.115 1.948,0.427 0.458,0.313 1.302,2.865 1.552,2 true 1.969,2.875 1.667,2 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 1.167,2.917 1.604,3.115 0.438,0.198 10 false TC0 1.875,2.917 2.313,3.115 0.438,0.198 10 false GC0
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-5 (TC0) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-6 (GC0) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-5 (TC0) - Body ground Ignition switch ON Below 1 V
z12-6 (GC0) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z12 battery ECU assembly connectors.


d.

Install the No. 1 HV battery hose.



OK

6.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

REPLACE NO.2 HV SUPPLY STACK SUB-ASSEMBLY

6.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

OK

NG

7.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
7.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)

OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY