The TCM receives the engine speed signal from the ECM via CAN communication and direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| P033531 | Crankshaft Position Sensor "A" No Signal | When the engine speed signal received from the ECM via CAN communication is 500 rpm or more, the signal received via direct line is 0 rpm for 5 seconds or more (1-trip detection logic). | ·
SFI system ·
ECM ·
TCM ·
Wire harness or connector ·
Certification ECU (Smart key ECU assembly) (w/ Entry and Start System) |
Comes on | DTC stored | Transmission | B | SAE Code:
P0335 |
The TCM detects malfunctions by comparing the engine speed signals received from the ECM via direct line and CAN communication.
If the TCM receives the engine speed signal via CAN communication but not via direct line, it will illuminate the MIL and store this DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait for 5 seconds or more.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P033531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
DATA LIST
The engine speed may be indicated as zero despite the engine running normally. This is caused by the NE signal not being received from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Start the engine.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
830 to 930 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Tester Display |
|---|
| Engine Speed |
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Entry and Start System | A |
| w/ Entry and Start System | B |
A
B
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
830 to 930 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Tester Display |
|---|
| Engine Speed |
The GTS display changes correctly in response to the engine speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the ECM connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,D71)Location & Routingewd_type=routing;type=c,c;code=A54,D71 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=16 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=13 |
||
| A54-16 (NEO) - D71-13 (NE) | Always | Below 1 Ω |
| A54-16 (NEO) or D71-13 (NE) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the ECM connector.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and wait for 5 seconds or more.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P033531 is output | B |
A
B
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P033562 is output | B |
A
B
Pre-procedure1
Disconnect the ECM connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,D71)Location & Routingewd_type=routing;type=c,c;code=A54,D71 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=16 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=13 |
||
| A54-16 (NEO) - D71-13 (NE) | Always | Below 1 Ω |
| A54-16 (NEO) or D71-13 (NE) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the ECM connector.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION