Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0441241 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071015  Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the TCM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The TCM applies voltage to the temperature sensor through TCM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority Note
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open The CVT fluid temperature sensor voltage is more than 4.915 V for 0.5 seconds when either of the following conditions is met (1-trip detection logic):
·

900 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were -29.375°C (-20.875°F) or less at engine start).

·

10 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were higher than -29.375°C (-20.875°F) at engine start).


·

Wire harness or connector

·

Transmission wire (CVT fluid temperature sensor)

·

TCM


Comes on DTC stored Transmission A SAE Code:
P0713

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 900 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were -29.375°C (-20.875°F) or less at engine start) ○ -
10 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were higher than -29.375°C (-20.875°F) at engine start) - ○
Malfunction Condition CVT fluid temperature sensor voltage is more than 4.915 V ○ ○
Duration 0.5 seconds or more 0.5 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

HINT:

This DTC is stored when either of the above detection patterns is met.


MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the TCM determines the CVT fluid temperature and can detect an open in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is more than 156 kΩ*, the TCM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.

*: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked in the Data List.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.

Wait for 15 minutes or more with the engine running.

5.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

6.

Input the DTC: P071015.

7.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)

Pre-procedure1

a.

Warm up the engine.


Procedure1

a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
Equal to ambient temperature: After cold soak If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



Post-procedure1

a.

None.



A

2.READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)

B

4.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
2.READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)

Pre-procedure1

a.

Warm up the engine.


Procedure1

a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
Approximately 100°C (212°F): After stall speed test If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



Post-procedure1

a.

None.



A

3.REPLACE TCM

B

4.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
3.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)

Pre-procedure1

a.
C397724C25
0.177,0.844 0.552,1.115 0.375,0.271 2.083,1.552 0.979,1.333 true 2.25,1.563 2.865,1.344 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.917,1.26 3.302,1.458 0.385,0.198 10 false OT+ 0.688,1.24 1.302,1.438 0.615,0.198 10 false OT- 0.25,0.906 0.604,1.083 0.354,0.177 10 false D74
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D74)Location & Routing

Click Connector(D74)Engine Compartment>Engine Wire>Transmission Wire

D74-11 (OT+) - D74-12 (OT-) Always 0.079 to 156 kΩ
D74-11 (OT+) - Other terminals Always 10 kΩ or higher
D74-12 (OT-)- Other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5.6 to 7.3 kΩ
25°C (77°F) 3.5 kΩ
110°C (230°F) 0.22 to 0.27 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the transmission wire connector.



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

Pre-procedure1

a.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-51 (THO1) - D71-52 (ETHO) Always 0.079 to 156 kΩ
D71-51 (THO1) - Other terminals Always 10 kΩ or higher
D71-52 (ETHO) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.



OK

6.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

6.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT