Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0441241 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P072012  Output Speed Sensor Circuit Short to Battery  P072014  Output Speed Sensor Circuit Short to Ground or Open  P072031  Output Speed Sensor No Signal  


DESCRIPTION

The transmission revolution sensor (NOUT) detects the output shaft speed and sends it to the TCM.

The TCM determines if belt mode has been entered by comparing the transmission revolution sensor (NOUT) and (NSS) signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority Note
P072012 Output Speed Sensor Circuit Short to Battery The transmission revolution sensor (NOUT) signal is normal but the transmission revolution sensor (NOUT) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

TCM


Comes on DTC stored Transmission A SAE Code:
P077D
P072014 Output Speed Sensor Circuit Short to Ground or Open The transmission revolution sensor (NOUT) signal is normal but the transmission revolution sensor (NOUT) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

TCM


Comes on DTC stored Transmission A SAE Code:
P077C
P072031 Output Speed Sensor No Signal Either of the following conditions is met for 5 seconds or more (1-trip detection logic):
·

When the transmission revolution sensor (NSS) signal indicates 350 rpm or more and the SPD signal indicates 11 km/h (7 mph) or more, the transmission revolution sensor (NOUT) signal indicates less than 300 rpm.

·

When the transmission revolution sensor (NC1) signal indicates 1180 rpm or more and the SPD signal indicates 11 km/h (7 mph) or more, the transmission revolution sensor (NOUT) signal indicates less than 300 rpm.


·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

TCM


Comes on DTC stored Transmission A SAE Code:
P0722

DTC Detection Condition Patterns (P072031):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The transmission revolution sensor (NSS) signal indicates 350 rpm or more ○ -
The transmission revolution sensor (NC1) signal indicates 1180 rpm or more - ○
The SPD signal indicates 11 km/h (7 mph) or more ○ ○
Malfunction Condition The transmission revolution sensor (NOUT) signal indicates less than 300 rpm ○ ○
Duration 5 seconds or more 5 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

MONITOR DESCRIPTION

The TCM receives signals from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.

If the TCM detects no signal from the transmission revolution sensor (NOUT) even while the vehicle is being driven, it will determine that the transmission revolution sensor (NOUT) is malfunctioning, illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

5.

Stop the vehicle.

6.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

7.

Input the DTC: P072012, P072014 or P072031.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C318994E61
0.25,2.844 3.771,3.042 3.521,0.198 10 false Transmission Revolution Sensor (NOUT) 5.979,3.073 6.5,3.365 0.521,0.292 10 false TCM 5.677,1.135 6.396,1.49 0.719,0.354 10 false NOB 5.406,1.135 5.865,1.333 0.458,0.198 10 false 26 2.083,1.125 2.542,1.323 0.458,0.198 10 false 2 1.656,1.125 2.219,1.365 0.563,0.24 10 false NOB 1.646,2.104 2.188,2.333 0.542,0.229 10 false NOO 2.073,2.104 2.531,2.302 0.458,0.198 10 false 1 5.406,2.104 5.865,2.302 0.458,0.198 10 false 10 5.677,2.104 6.135,2.302 0.458,0.198 10 false NOO 5.979,2.917 6.438,3.115 0.458,0.198 10 false D71 0.25,2.677 0.708,2.875 0.458,0.198 10 false D62 6.302,0.958 6.76,1.156 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (NO SENSOR VOLTAGE)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NO Sensor Voltage Transmission revolution sensor (NOUT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Transmission > Data List
Tester Display
NO Sensor Voltage
50003 373 928
Result:
Result Proceed to
The value of NO Sensor Voltage is between 0.2 and 1.8 V A
None of the above conditions are met B




A

2.READ VALUE USING GTS (NO SENSOR SPEED)

B

5.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
2.READ VALUE USING GTS (NO SENSOR SPEED)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NO Sensor Speed Output shaft speed (NOUT) Min.: 0 rpm
Max.: 65535 rpm
0 rpm: Vehicle stopped -
Powertrain > Transmission > Data List
Tester Display
NO Sensor Speed
50003 373 927
Result:
Result Proceed to
The value of NO Sensor Speed is 0 rpm A
None of the above conditions are met B




A

3.READ VALUE USING GTS (NO SENSOR SPEED)

B

5.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
3.READ VALUE USING GTS (NO SENSOR SPEED)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NSS Sensor Speed Secondary pulley speed (NSS) Min.: 0 rpm
Max.: 65535 rpm
Equal to NO Sensor Speed: Vehicle being driven in belt mode -
NO Sensor Speed Output shaft speed (NOUT) Min.: 0 rpm
Max.: 65535 rpm
Equal to NSS Sensor Speed: Vehicle being driven in belt mode -
Shift Mode Shift mode status Gear Mode or Belt Mode - -
Powertrain > Transmission > Data List
Tester Display
NSS Sensor Speed
NO Sensor Speed
Shift Mode
50003 373 925,927,938
Result:
Result Proceed to
The value of NSS Sensor Speed and NO Sensor Speed are the same A
The value of NSS Sensor Speed and NO Sensor Speed are different B




A

4.REPLACE TCM

B

5.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
4.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

Pre-procedure1

a.

Remove the transmission revolution sensor (NOUT).

HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>REVOLUTION SENSOR (NOUT SENSOR)>REMOVAL



b.

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.

C397726C22
1.531,2.135 1.969,2.375 0.438,0.24 1.448,1.833 1.615,1.417 true 2.083,1.833 1.917,1.417 true 4.083,1.104 4.333,1.354 true 4.625,1.354 4.875,1.604 true 5.854,0.917 6.167,1.073 0.313,0.156 10 false *1 5.125,0.573 5.438,0.729 0.313,0.156 10 false *2 1.208,0.656 1.521,0.813 0.313,0.156 10 false *a 4.646,1.823 4.958,1.979 0.313,0.156 10 false *b 3.781,2.229 4.094,2.385 0.313,0.156 10 false *c 1.313,1.854 1.771,2.052 0.458,0.198 10 false NOB 1.969,1.854 2.427,2.052 0.458,0.198 10 false NOO 3.969,1.021 4.125,1.219 0.156,0.198 10 false 2 4.917,1.552 5.073,1.75 0.156,0.198 10 false 1 1.635,2.188 1.958,2.354 0.323,0.167 10 false D62
*1 Battery *2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NOUT))
*b Magnet
*c 5 mm or less - -



c.

Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NOUT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.



Procedure1

a.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition

Click Location & Routing(D62)Location & Routing

Click Connector(D62)Engine Compartment>Engine Wire>Transmission Revolution Sensor (NOUT)

D62-1 (NOO) - D62-2 (NOB) Low signal 4 to 8 mA
D62-1 (NOO) - D62-2 (NOB) High signal 12 to 16 mA


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - TCM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NOUT)

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - TCM)

Pre-procedure1

a.

Disconnect the transmission revolution sensor (NOUT) connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D62,D71)Location & Routing

Click Connector(D62)Engine Compartment>Engine Wire>Transmission Revolution Sensor (NOUT)

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D62-1 (NOO) - D71-10 (NOO) Always Below 1 Ω
D62-2 (NOB) - D71-26 (NOB) Always Below 1 Ω
D62-1 (NOO) or D71-10 (NOO) - Body ground and other terminals Always 10 kΩ or higher
D62-2 (NOB) or D71-26 (NOB) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the transmission revolution sensor (NOUT) connector.



OK

7.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - TCM)

7.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT