Home › Drivetrain › K320 (MULTIDRIVE / CVT) › REVOLUTION SENSOR (NOUT SENSOR)
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438044 REVOLUTION SENSOR(NOUT SENSOR) A

K320 MULTIDRIVE / CVT  REVOLUTION SENSOR(NOUT SENSOR)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446031N06
1.938,1.083 2.271,1.083 false 1.958,1.771 2.292,1.771 false 2.031,2.583 2.365,2.583 false 6.448,0.25 6.781,0.25 false 6.417,0.698 6.75,0.698 false 4.563,1.073 4.896,1.073 false 5.677,2.208 6.01,2.208 false 6.25,0.094 6.531,0.448 0.281,0.354 18 false 1 6.24,0.542 6.521,0.896 0.281,0.354 18 false 2 2.333,0.948 2.615,1.302 0.281,0.354 18 false 3 2.385,1.615 2.667,1.969 0.281,0.354 18 false 4 2.438,2.427 2.719,2.781 0.281,0.354 18 false 5 4.365,0.927 4.646,1.281 0.281,0.354 18 false 6 6.052,2.063 6.333,2.417 0.281,0.354 18 false 7 5.385,1.583 5.635,1.75 0.25,0.167 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
4 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
5 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
6 ECM 89661 - - -
7 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C428875N03
4.083,0.75 4.5,0.75 false 3.5,1.083 3.917,1.083 false 4.552,0.635 4.833,0.99 0.281,0.354 18 false 8 3.375,0.99 3.656,1.344 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

8 TRANSMISSION REVOLUTION SENSOR (NOUT) 89413M - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission revolution sensor (NOUT) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 4.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 89413M 8.REMOVE TRANSMISSION REVOLUTION SENSOR (NOUT)

a.
C431082