A magnet is installed to the shift fork. When the TCM commands the S1 synchronizer to move, the shift fork moves the S1 synchronizer together with the magnet.
The Hall IC built into the shift stroke sensor converts the magnet position into a voltage signal and sends it to the TCM. The TCM judges the S1 synchronizer operating condition (whether the S1 synchronizer is engaged or released) based on this signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| P091412 | Gear Shift Position Circuit Short to Battery | A short to +B is detected in the shift stroke sensor circuit for 5 seconds or more (1-trip detection logic). | ·
Shift stroke sensor ·
Harness and connector ·
TCM |
Comes on | DTC stored | Transmission | A | SAE Code:
P0917 |
This DTC indicates a short to +B in the shift stroke sensor circuit. If there is a short to +B in the shift stroke sensor circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Perform the D Position Test inspection in Road Test.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P091412.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Pre-procedure1
Disconnect the shift stroke sensor connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D69)Location & Routingewd_type=routing;type=c;code=D69 Click Connector(D69)Engine Compartment>Engine Wire>Shift Stroke Sensorewd_type=component;type=c;code=D69;pinno=2,3 |
||
| D69-2 (VDD) - D69-3 (GND) | Ignition switch ON | 4.7 to 5.3 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Connect the shift stroke sensor connector.
OK
NG
Pre-procedure1
Disconnect the shift stroke sensor connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D69,D71)Location & Routingewd_type=routing;type=c,c;code=D69,D71 Click Connector(D69)Engine Compartment>Engine Wire>Shift Stroke Sensorewd_type=component;type=c;code=D69;pinno=4 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=46 |
||
| D69-4 (VOUT) or D71-46 (SFV) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the shift stroke sensor connector.
OK
NG
Pre-procedure1
Connect 3 new dry-cell batteries (1.5 V each) in series.
Prepare a magnet or equivalent tool.
Remove the shift stroke sensor.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>SHIFT STROKE SENSOR>REMOVAL
Connect a positive (+) lead from the batteries to terminal 2 (VDD) and a negative (-) lead to terminal 3 (GND).
| *a | Component without harness connected
(Shift Stroke Sensor) |
*b | Magnet Movement Direction |
| *c | Dry Cell Battery | *d | Magnet |
| *e | 2.6 mm or less | - | - |
Procedure1
Wave the magnet left and right 2.6 mm (0.102 in.) or less from the tip of the shift stroke sensor to output a high/low signal while measuring the voltage.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D69)Location & Routingewd_type=routing;type=c;code=D69 Click Connector(D69)Engine Compartment>Engine Wire>Shift Stroke Sensorewd_type=component;type=c;code=D69;pinno=4,3 |
||
| D69-4 (VOUT) - D69-3 (GND) | High signal | 4.09 to 4.19 V |
| D69-4 (VOUT) - D69-3 (GND) | Low signal | 0.36 to 0.45 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D69)Location & Routingewd_type=routing;type=c;code=D69 Click Connector(D69)Engine Compartment>Engine Wire>Shift Stroke Sensorewd_type=component;type=c;code=D69;pinno=4,3 |
||
| D69-4 (VOUT) - D69-3 (GND) | High signal | 4.55 to 4.65 V |
| D69-4 (VOUT) - D69-3 (GND) | Low signal | 0.4 to 0.5 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the shift stroke sensor.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the shift stroke sensor connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D69,D71)Location & Routingewd_type=routing;type=c,c;code=D69,D71 Click Connector(D69)Engine Compartment>Engine Wire>Shift Stroke Sensorewd_type=component;type=c;code=D69;pinno=2 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=45 |
||
| D69-2 (VDD) or D71-45 (VCSF) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the shift stroke sensor connector.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION