The TCM communicates with the ECM via CAN communication.
If a problem occurs in this communication, the TCM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | No communication between the TCM and ECM for 1.25 seconds or more (1-trip detection logic) | ·
Harness and connector ·
ECM ·
TCM |
Comes on | DTC stored | Transmission | A | SAE Code:
U0100 |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 3 seconds or more.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: U010087.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Pre-procedure1
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO. 1 Relay |
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54)Location & Routingewd_type=routing;type=c;code=A54 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=9,35 |
||
| 3 (EFI-MAIN NO. 1 relay) - A54-9 (+B) | Always | Below 1 Ω |
| 3 (EFI-MAIN NO. 1 relay) - A54-35 (+B2) | Always | Below 1 Ω |
| 3 (EFI-MAIN NO. 1 relay), A54-9 (+B) or A54-35 (+B2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the ECM connector.
Install the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Write down the currently output DTCs before clearing them.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| U010087 is output | B |
Post-procedure1
None.
A
B
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION