This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and Display Receiver Assembly ·
Telematics transceiver* |
Navigation System | A |
*: Telematics Transceiver
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Telematics Transceiver | A |
| w/o Telematics Transceiver | B |
A
B
Pre-procedure1
Disconnect the H83 radio and display receiver assembly connectors.
Disconnect the H84 telematics transceiver connector.
Disconnect the H88 front No. 2 speaker assembly RH connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,H88,H84,M2,N2)Location & Routingewd_type=routing;type=c,c,c,c,c;code=H83,H88,H84,M2,N2 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=1,6,2,7,4,9,3,8 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=3,1 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=1,2 Click Connector(M2)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=M2;pinno=2,1 Click Connector(N2)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=N2;pinno=2,1 |
||
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H84-1 (SP+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H84-2 (SPI-) - Body ground | Always | 10 kΩ or higher |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the telematics transceiver.
Procedure1
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H84)Location & Routingewd_type=routing;type=c;code=H84 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=1,3,2,4 |
||
| H84-1 (SPI+) - H84-3 (SPO+) | Always | Below 1 Ω |
| H84-2 (SPI-) - H84-4 (SPO-) | Always | Below 1 Ω |
| H84-1 (SPI+) - H84-2 (SPI-) | Always | 10 kΩ or higher |
| H84-3 (SPO+) - H84-4 (SPO-) | Always | 10 kΩ or higher |
| H84-1 (SPI+) or H84-3 (SPO+) - Body ground | Always | 10 kΩ or higher |
| H84-2 (SPI-) or H84-4 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H87 front No. 2 speaker assembly LH connector.
Disconnect the H84 telematics transceiver connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H87,H84)Location & Routingewd_type=routing;type=c,c;code=H87,H84 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=3,1 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=3,4 |
||
| H87-3 (+) or H84-3 (SPO+) - Body ground | Always | 10 kΩ or higher |
| H87-1 (-) or H84-4 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H88,K2,H87,L2)Location & Routingewd_type=routing;type=c,c,c,c;code=H88,K2,H87,L2 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=4,2 Click Connector(K2)Body>Front Door Wire RH / Television Camera Wire>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=K2;pinno=2,1 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=4,2 Click Connector(L2)Body>Front Door Wire LH / Television Camera Wire>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=L2;pinno=2,1 |
||
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Pre-procedure1
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Disconnect the M2 and N2 rear speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,H88,H87,M2,N2)Location & Routingewd_type=routing;type=c,c,c,c,c;code=H83,H88,H87,M2,N2 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=1,6,2,7,4,9,3,8 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=3,1 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=3,1 Click Connector(M2)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=M2;pinno=2,1 Click Connector(N2)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=N2;pinno=2,1 |
||
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H88,K2,H87,L2)Location & Routingewd_type=routing;type=c,c,c,c;code=H88,K2,H87,L2 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=4,2 Click Connector(K2)Body>Front Door Wire RH / Television Camera Wire>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=K2;pinno=2,1 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=4,2 Click Connector(L2)Body>Front Door Wire LH / Television Camera Wire>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=L2;pinno=2,1 |
||
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B