The power back door controls the multiplex network door ECU and operates the power back door unit assembly and back door lock assembly.
If the power back door does not operate using any of the operations, a malfunction related to the power back door operation conditions or multiplex network door ECU are possible causes.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect fuses for circuits related to this system before performing the following inspection procedure.
This check is possible only when the "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "On" (The default setting is "On").
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
Check that the power back door function on the multi-information display in the combination meter assembly is set to ON.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
| Result | Proceed to |
|---|---|
| Power back door function on the multi-information display in the combination meter assembly is set to ON (power back door system operation is permitted) | A |
| Power back door function on the multi-information display in the combination meter assembly is set to OFF (power back door system operation is prohibited) | B |
A
B
Check the power back door system condition.
| Result | Proceed to |
|---|---|
| The malfunction symptom reproduces | A |
| The malfunction symptom does not reproduce | B |
A
B
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>Power Back Door cannot be Operated Frequently
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
Disconnect the multiplex network door ECU connectors.
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y28)Location & Routingewd_type=routing;type=c;code=Y28 Click Connector(Y28)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y28;pinno=4 |
||
| Y28-4 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y30,Y27)Location & Routingewd_type=routing;type=c,c;code=Y30,Y27 Click Connector(Y30)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y30;pinno=7,9 Click Connector(Y27)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y27;pinno=5 |
||
| Y30-7 (ECUB) - Body ground | Ignition switch off | 11 to 14 V |
| Y27-5 (B) - Body ground | Ignition switch off | 11 to 14 V |
| Y30-9 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Diagnostic Note |
|---|---|---|---|
| PBD Main Switch | Power back door ON/OFF signal | ON or OFF | ON: Power back door ON
OFF: Power back door off |
| Door Lock Signal | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
| Tester Display |
|---|
| PBD Main Switch |
| Door Lock Signal |
| Result | Proceed to |
|---|---|
| Either item is normal | A |
| "PBD Main SW" item does not switch to "ON" or "OFF" according to main switch operation | B |
| "Door Lock Signal" item does not switch to "Lock" or "Unlock" according to operation to lock or unlock all doors | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| PBD Touch Sensor RH | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor LH | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Tester Display |
|---|
| PBD Touch Sensor RH |
| PBD Touch Sensor LH |
| Result | Proceed to |
|---|---|
| On the GTS screen, ON or OFF is displayed accordingly | A |
| On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH | B |
| On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH | C |
A
B
C
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y26 power back door sensor assembly RH connector.
Disconnect the Y29 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y26,Y29)Location & Routingewd_type=routing;type=c,c;code=Y26,Y29 Click Connector(Y26)Body>No. 2 Back Door Wire>Power Back Door Sensor Assembly LHewd_type=component;type=c;code=Y26;pinno=1,2 Click Connector(Y29)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y29;pinno=8,9 |
||
| Y26-1 (OSR) - Y29-8 (OSR) | Always | Below 1 Ω |
| Y26-2 (OSRE) - Y29-9 (OSE) | Always | Below 1 Ω |
| Y26-1 (OSR) or Y29-8 (OSR) - Body ground | Always | 10 kΩ or higher |
| Y26-2 (OSRE) or Y29-9 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H135 main body ECU (multiplex network body ECU) connector.
Disconnect the Y30 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y30,H135)Location & Routingewd_type=routing;type=c,c;code=Y30,H135 Click Connector(Y30)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y30;pinno=11 Click Connector(H135)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H135;pinno=7 |
||
| Y30-11 (LIB) - H135-7 (LSBO) | Always | Below 1 Ω |
| Y30-11 (LIB) or H135-7 (LSBO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Main Body ECU [Multiplex Network Body ECU]) |
Remove the main body ECU (multiplex network body ECU) with the connector(s) still connected.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H135)Location & Routingewd_type=routing;type=c;code=H135 Click Connector(H135)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H135;pinno=7 |
||
| H135-7 (LSBO) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y25 power back door sensor assembly LH connector.
Disconnect the Y29 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Y25,Y29)Location & Routingewd_type=routing;type=c,c;code=Y25,Y29 Click Connector(Y25)Body>No. 2 Back Door Wire>Power Back Door Sensor Assembly RHewd_type=component;type=c;code=Y25;pinno=1,2 Click Connector(Y29)Body>No. 2 Back Door Wire>Multiplex Network Door ECUewd_type=component;type=c;code=Y29;pinno=1,9 |
||
| Y25-1 (OSL) - Y29-1 (OSL) | Always | Below 1 Ω |
| Y25-2 (OSLE) - Y29-9 (OSE) | Always | Below 1 Ω |
| Y25-1 (OSL) or Y29-1 (OSL) - Body ground | Always | 10 kΩ or higher |
| Y25-2 (OSLE) or Y29-9 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG