Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT (for 2WD) › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441824 REAR AXLE HUB BOLT(for 2WD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT(for 2WD)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear axle hub bolt replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE REAR WHEEL

Hide 890C0A 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C444348

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




Hide 5.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C444349

Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle beam assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.



Hide 42431 6.REMOVE REAR DISC

Hide 42312E 7.REMOVE REAR AXLE HUB BOLT

a.
C444350C01
1.583,0.458 1.688,0.844 true 1.167,1.427 0.802,1.104 0.802,1.104 1.125,1.083 true 1.281,0.385 1.573,0.542 0.292,0.156 10 true SST 0.573,1 0.781,1.188 0.208,0.188 10 true *a 1.938,1.771 2.146,1.958 0.208,0.188 10 true *c 0.688,1.969 0.896,2.156 0.208,0.188 10 false *b
*a Service Nut
*b Hold
*c Turn


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 8.INSTALL REAR AXLE HUB BOLT

a.

Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.
C444352C01
1.208,1.365 0.708,1.281 0.708,1.281 1.063,1.083 true 2.167,0.365 2.531,0.427 true 2.292,0.125 2.896,0.292 true 0.479,1.219 0.688,1.385 0.208,0.167 10 true *a 2.073,0.042 2.271,0.198 0.198,0.156 10 true *b 0.677,1.979 0.99,2.135 0.313,0.156 10 false *c 2.229,1.302 2.542,1.458 0.313,0.156 10 false *d 1.979,0.271 2.208,0.448 0.229,0.177 10 false *a
*a Service Nut
*b Washer
*c Hold
*d Turn


Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 9.INSTALL REAR DISC

Hide 10.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly to the rear axle beam assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)

NOTICE:

Do not twist the rear flexible hose when installing the front disc brake caliper assembly.



Hide 890C0A 11.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 13.INSTALL REAR WHEEL

Hide 14. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART