Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT › 2020.08–2021.07
RM3700E _53 Suspension _093737 FRONT SUSPENSION _0441837 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C443117N03
4.521,1.344 4.854,1.344 false 3.844,3.396 4.229,3.396 false 2.135,1.063 2.469,1.063 false 4.906,1.177 5.188,1.531 0.281,0.354 18 false 1 4.573,3.24 4.854,3.594 0.281,0.354 18 false 2 2,0.958 2.198,1.156 0.198,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE ASSEMBLY - - - -
2 FRONT LOWER BALL JOINT ASSEMBLY 43340A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C443119C02
1.219,3.521 1.219,2.646 1.219,2.646 1.448,2.646 true 1.344,3.531 1.344,2.646 true 4.396,2.677 4.927,2.792 false 5.698,3.448 6.333,3.208 true 6.229,2.865 6.521,2.865 false 4.198,4.531 4.375,4.323 false 1.5,2.542 1.958,2.74 0.458,0.198 10 false SST 3.073,3.448 3.427,3.729 0.354,0.281 10 false *a 0.438,0.094 0.781,0.521 0.344,0.427 18 false i 4.458,0.771 4.708,1.063 0.25,0.292 18 true iii 0.521,2.698 1.25,3.021 0.729,0.323 18 false iv 4.083,1.979 4.813,2.302 0.729,0.323 18 false v 4.073,2.583 4.531,2.781 0.458,0.198 10 false SST 6.375,3.104 6.833,3.302 0.458,0.198 10 false *e 6.844,2.031 7.083,2.281 0.24,0.25 10 false *c 6.844,2.354 7.083,2.604 0.24,0.25 10 false *c 6.063,2.771 6.302,3.021 0.24,0.25 10 false *d 4.031,4.49 4.49,4.688 0.458,0.198 10 false *b 5.083,3.844 5.542,4.042 0.458,0.198 10 false A 5.083,4.094 5.542,4.292 0.458,0.198 10 false B 5.25,0.948 5.448,1.25 0.198,0.302 18 true ii
*a 1 mm (0.0394 in.) *b Center Nut
*c Molybdenum Grease Application Area *d Place wrench here
*e String - -
V113147

Turn - -


i.

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Remove the cotter pin.


iii.

Remove the nut.


iv.

Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



v.

Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.