Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441810 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C443130C02
1.01,1.688 0.885,1.021 0.885,1.021 0.719,1.021 false 2.667,2.104 3.146,0.615 3.146,0.615 3.333,0.615 false 3.417,1.563 3.573,1.208 3.573,1.208 3.771,1.208 false 4.156,3.698 4.198,3.104 4.198,3.104 4.354,3.104 false 3.146,3.865 3.354,4.604 3.354,4.604 3.552,4.604 false 2.24,4.427 2.365,4.333 2.365,4.333 2.563,4.333 false 0.573,4.302 0.802,5.01 0.802,5.01 1.01,5.01 false 6.469,0.24 6.802,0.24 false 6.094,5.25 6.219,5.563 6.219,5.563 6.385,5.563 false 4.719,1.323 5.167,1.323 false 3.708,2.552 3.969,2.552 false 6.083,2.146 6.198,2.427 6.198,2.427 6.396,2.427 false 0.354,0.885 0.906,1.24 0.552,0.354 18 false 10 1.292,4.833 1.844,5.188 0.552,0.354 18 false 7 2.615,4.208 3.167,4.563 0.552,0.354 18 false 9 3.844,4.438 4.396,4.792 0.552,0.354 18 false 8 6.427,5.385 6.979,5.74 0.552,0.354 18 false 3 4.729,2.958 5.281,3.313 0.552,0.354 18 false 4 6.448,2.313 7,2.667 0.552,0.354 10 false *1 5.396,1.177 5.948,1.531 0.552,0.354 18 false 5 4.031,1.052 4.583,1.406 0.552,0.354 18 false 6 3.563,0.448 4.115,0.802 0.552,0.354 18 false 11 6.052,0.115 6.604,0.469 0.552,0.354 18 false 2 1.573,1.323 1.844,1.542 0.271,0.219 10 false x2 2.417,4.948 2.688,5.167 0.271,0.219 10 false x2 4.01,2.49 4.167,2.688 0.156,0.198 10 false ● 0.396,3.125 0.667,3.344 0.271,0.219 10 false x2 4.573,3.01 4.74,3.208 0.167,0.198 10 false ● 2.677,1.271 2.948,1.49 0.271,0.219 10 false x2 5.708,0.177 6.26,0.531 0.552,0.354 10 false (*A), 5.531,0.115 5.76,0.438 0.229,0.323 18 false 1 6.208,0.177 6.76,0.531 0.552,0.354 10 false (*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 FRONT WHEEL - - - -
4 FRONT AXLE SHAFT NUT 43502H (Click here) - -
5 FRONT SPEED SENSOR 89543 (Click here) - -
6 TIE ROD END SUB-ASSEMBLY 45047 (Click here) - -
7 FRONT DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
8 FRONT DISC 43512 (Click here) - -
9 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 48069 (Click here) - -
10 FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -
11 FRONT AXLE ASSEMBLY - (Click here) -

*A for HV Model - -
*1 FRONT FLEXIBLE HOSE - -
● Non-reusable part - -

C443131C02
5.615,2.854 5.813,2.313 5.813,2.313 5.979,2.313 false 4.063,1.323 4.26,0.781 4.26,0.781 4.427,0.781 false 2.24,0.813 2.385,0.385 2.385,0.385 2.552,0.385 false 2.594,0.302 2.906,0.5 0.313,0.198 10 false *1 4.458,0.615 4.896,0.969 0.438,0.354 18 false 13 6.229,2.156 6.667,2.51 0.438,0.354 18 false 12 0.906,0.438 1.219,0.635 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

12 FRONT AXLE HUB SUB-ASSEMBLY 43502C (Click here) - -
13 FRONT DISC BRAKE DUST COVER 47782 - - -

*1 STEERING KNUCKLE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE


Hide 2. DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE FRONT WHEEL

Hide 43502H 4.REMOVE FRONT AXLE SHAFT NUT

Z101186

Click here(Click here)

Hide 89543 5.SEPARATE FRONT SPEED SENSOR

a.
C443132N01
0.406,0.094 0.688,0.448 0.281,0.354 18 false i 4.104,0.104 4.385,0.458 0.281,0.354 18 false ii

i.

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



ii.

Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.





Hide 45047 6.SEPARATE TIE ROD END SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 7.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 43512 8.REMOVE FRONT DISC

Z101186

Click here(Click here)

Hide 48069 9.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C444459


Hide 43420 10.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C443133C02
2.906,0.26 3.323,0.26 3.323,0.26 3.323,0.979 true 2.99,0.469 3.323,0.469 true 3.24,0.979 3.448,1.156 0.208,0.177 10 true *a 0.417,0.063 0.635,0.344 0.219,0.281 18 false i 3.719,0.073 3.948,0.365 0.229,0.292 18 true ii
*a Matchmark - -


i.

Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


ii.

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.




Hide 11.REMOVE FRONT AXLE ASSEMBLY

a.
C443134N01
0.406,0.063 0.688,0.417 0.281,0.354 18 false i

i.

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.




Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C443135N01
0.406,0.073 0.813,0.406 0.406,0.333 18 false i, ii

i.

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



ii.

Using a 12 mm hexagon socket wrench, remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.





Hide 47782 13.REMOVE FRONT DISC BRAKE DUST COVER

a.
C443136