| *A | for 2WD | *B | Width Across Flats 17mm nut |
| *C | Width Across Flats 14mm nut | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a ball joint lock nut wrench
For use with SST |
Use the same procedure for the RH side and LH side
The following procedure is for the LH side.
48760B
1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY
48540
2.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY
for 2WD:
Insert the upper end of the rear shock absorber assembly with rear suspension support assembly into the vehicle body, temporarily install the rear shock absorber assembly to the rear axle beam assembly with the bolt and nut.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
for AWD:
Insert the upper end of the rear shock absorber assembly with rear suspension support assembly into the vehicle body, temporarily install the rear shock absorber assembly to the rear No. 1 suspension arm assembly with the bolt.
48755
3.INSTALL REAR SUSPENSION SUPPORT
| *a | Correct | *b | Incorrect |
Install the rear suspension support to the rear shock absorber assembly.
Make sure that the rear suspension support is correctly installed as shown in the illustration.
48597A
4.INSTALL REAR SHOCK ABSORBER CUSHION RETAINER
Width Across Flats 17mm nut:
| *a | Torque Wrench Fulcrum Length | *b | Rear Shock Absorber Cushion Retainer |
| *c | Collar | - | - |
Install the rear shock absorber cushion retainer to the rear shock absorber assembly
While using a 5 mm hexagon socket wrench to hold the rear shock absorber assembly in place, use a ball joint lock nut wrench to tighten the nut until the rear shock absorber cushion retainer is seated to the collar of the rear suspension support assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a ball joint lock nut wrench (fulcrum length of 155.5 mm (6.12 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.))) : 7.7 N*m (79 kgf*cm, 68 in.*lbf))
Width Across Flats 14mm nut:
| *a | Torque Wrench Fulcrum Length | *b | Rear Shock Absorber Cushion Retainer |
| *c | Collar | *d | Turn |
| *e | Hold | - | - |
Install the rear shock absorber cushion retainer to the rear shock absorber assembly
While using a 5 mm hexagon socket wrench to hold the rear shock absorber assembly in place, use a SST to tighten the nut until the rear shock absorber cushion retainer is seated to the collar of the rear suspension support assembly.
Calculate the torque wrench reading when changing the fulcrum length of thetorque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a SST(fulcrum length of 200 mm (7.87 in.))+ torque wrench (fulcrum length of 162 mm (6.38 in.))) : 6.7 N*m (68 kgf*cm,59 in.*lbf))
64715C
5.INSTALL DECK SIDE TRIM COVER
6.INSTALL REAR WHEEL
48540
8.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY
for 2WD:
Fully tighten the rear shock absorber assembly (lower side) with the bolt while keeping the nut from rotating.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
for AWD:
Fully tighten the rear shock absorber assembly (lower side) with the bolt.
9.INSPECT AND ADJUST REAR WHEEL ALIGNMENT