Home › Drivetrain › Q510 (HYBRID TRANSMISSION / TRANSAXLE) › DIFFERENTIAL SIDE GEAR SHAFT
RM3700E _52 Drivetrain _093740 Q510 HYBRID TRANSMISSION / TRANSAXLE _0441873 DIFFERENTIAL SIDE GEAR SHAFT A

Q510 HYBRID TRANSMISSION / TRANSAXLE  DIFFERENTIAL SIDE GEAR SHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C442383N02
6.469,0.844 6.802,0.844 false 4.615,0.969 4.948,0.969 false 5.583,1.531 5.917,1.531 false 4.969,4.271 4.969,4.698 false 4.625,3.385 4.458,3.385 4.458,3.385 4.375,3.802 false 2.313,2.031 2.146,2.031 2.146,2.031 2.063,2.448 false 1.656,2.417 1.656,2.771 false 0.854,2.073 0.76,2.354 0.76,2.354 0.76,2.521 false 6.479,0.25 6.813,0.25 false 6.083,5.104 6,5.25 6,5.25 6,5.417 false 6.229,0.677 6.51,1.031 0.281,0.354 18 false 6 5.031,0.792 5.313,1.146 0.281,0.354 18 false 5 5.979,1.365 6.26,1.719 0.281,0.354 18 false 5 6.073,5.375 6.354,5.729 0.281,0.354 18 false 3 5.198,4.646 5.479,5 0.281,0.354 18 false 1 1.719,2.76 2,3.115 0.281,0.354 18 false 2 0.802,2.531 1.083,2.885 0.281,0.354 18 false 4 2.354,1.906 2.573,2.125 0.219,0.219 10 false ● 4.677,3.26 4.896,3.479 0.219,0.219 10 false ● 5.979,0.094 6.583,0.438 0.604,0.344 18 false 7, 8 1.573,2.792 1.792,3.01 0.219,0.219 10 false ● 5.052,4.708 5.271,4.927 0.219,0.219 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DIFFERENTIAL SIDE GEAR SHAFT DUST COVER LH 41336M (Click here) - -
2 DIFFERENTIAL SIDE GEAR SHAFT DUST COVER RH 41336L (Click here) - -
3 DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY LH 41309L (Click here) - -
4 DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH 41309K (Click here) - -
5 REAR DRIVE SHAFT ASSEMBLY - - - -
6 ADD HYBRID TRANSAXLE FLUID - - (Click here) -
7 INSPECT HYBRID TRANSAXLE FLUID - (Click here) - -
8 INSPECT FOR HYBRID TRANSAXLE FLUID LEAK - (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 41336M 1.INSTALL DIFFERENTIAL SIDE GEAR SHAFT DUST COVER LH

Z101186

NOTICE:
·

Be sure install the differential side gear shaft dust cover LH so that there is no clearance between the edge of the differential side gear shaft dust cover LH and differential side gear shaft sub-assembly LH.

·

Do not damage the differential side gear shaft dust cover LH.




a.
C449598C01
3.063,0.135 3.396,0.135 false 2.219,0.458 2.552,0.458 false 2.76,1.052 2.333,0.865 2.333,0.865 3.073,0.99 false 0.385,0.042 0.667,0.396 0.281,0.354 18 false i 2.844,0.052 3.156,0.25 0.313,0.198 10 false *a 2.01,0.396 2.323,0.594 0.313,0.198 10 false *b 2.052,0.792 2.448,1 0.396,0.208 10 false SST
*a Press *b Steel Plate


i.

Using SST, a steel plate and press, install a new differential side gear shaft dust cover LH to the differential side gear shaft sub-assembly LH.

SST
09316-20011  
09527-20011  



Hide 41336L 2.INSTALL DIFFERENTIAL SIDE GEAR SHAFT DUST COVER RH

Hide 41309L 3.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY LH

a.
C442384C01
4.875,0.896 5.208,0.896 true 5.365,3.573 5.677,3.771 0.313,0.198 10 false *a 4.51,0.802 4.833,0.948 0.323,0.146 10 true SST 0.427,1.115 0.729,1.417 0.302,0.302 18 false i 4.302,0.125 4.604,0.427 0.302,0.302 18 true ii 4.271,2.156 4.573,2.458 0.302,0.302 18 true iii
*a Less than 421.1 mm (1.38 ft.) - -


i.

Using a brass bar and hammer, install a new snap ring to the differential side gear shaft sub-assembly LH.


ii.

Using SST, install the differential side gear shaft sub-assembly LH to the rear traction motor with transaxle assembly.

SST
09520-24010  (09520-04010, 09520-32040)

NOTICE:
·

Position the snap ring with its end gap facing downward.

·

Do not install the differential side gear shaft sub-assembly LH at an angle. If the differential side gear shaft sub-assembly LH is installed at an angle, replace the snap ring with a new one.

·

Do not damage the differential side gear shaft LH type T oil seal.




iii.

Measure the distance between the right differential side gear shaft sub-assembly and left differential side gear shaft sub-assembly as shown in the illustration.

Standard Distance:

Less than 421.1 mm (1.38 ft.)




Hide 41309K 4.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH