This DTC is stored when CXPI communication between the semiconductor power integration ECU, power distribution box assembly, windshield wiper relay assembly or light control LED ECU and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B235287 | Power Integration No.1 System Missing Message | No communication between semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Semiconductor power integration ECU ·
Harness or connector |
Main Body | B |
| B235587 | Power Distribution Box Missing Message | No communication between power distribution box assembly and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Power distribution box assembly |
Main Body | B |
| B235787 | Wiper Module Missing Message | No communication between windshield wiper relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Windshield wiper relay assembly ·
Harness or connector |
Main Body | B |
| B235887 | Smart LDM Left Missing Message | No communication between light control LED ECU LH and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Light control LED ECU LH ·
Harness or connector |
Main Body | B |
| B235987 | Smart LDM Right Missing Message | No communication between light control LED ECU RH and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Light control LED ECU RH ·
Harness or connector |
Main Body | B |
Inspect the fuses for circuits related to this system before performing the following procedure.
Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Clear the DTCs.
| Result |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| B235287, B235587, B235787, B235887 and B235987 are output | A |
| B235287, B235787, B235887 and B235987 are output | B |
| Only B235587 is output | C |
| Only B235287 is output | D |
| Only B235787 is output | E |
| Only B235887 is output | F |
| Only B235987 is output | G |
| DTCs are not output | H |
A
B
C
D
E
F
G
H
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Remove the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Disconnect the 4D power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Output DTC |
|---|---|---|---|
| MB-22 (CXPI) - 4D-5 | Always | Below 1 Ω | B235287,B235587,B235787,B235887,B235987 |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Disconnect the 4D power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-22 (CXPI) - 4D-5 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4D power distribution box assembly connector.
Disconnect the A49 windshield wiper relay assembly connector.
Disconnect the A4 light control LED ECU LH connector.
Disconnect the A5 light control LED ECU RH connector.
Disconnect the A86 semiconductor power integration ECU connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A86)Location & Routingewd_type=routing;type=c;code=A86 Click Connector(A86)Engine Compartment>Engine Room Main Wire>Semiconductor Power Integration ECUewd_type=component;type=c;code=A86;pinno=8 |
||
| 4D-5 - A86-8 (CXPI) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| 4D-5 - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4B and 4C power distribution box assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-41 (GND1) - Body ground | Always | Below 1 Ω |
| 4B-44 (GND2) - Body ground | Always | Below 1 Ω |
| 4B-36 (GND3) - Body ground | Always | Below 1 Ω |
| 4C-25 (GND4) - Body ground | Always | Below 1 Ω |
Post-procedure1
Connect the cable to the negative (-) auxiliary battery terminal.
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4G-1 (+B1) - Body ground | Ignition switch off | 11 to 14 V |
| 4F-1 (+B2) - Body ground | Ignition switch off | 11 to 14 V |
| 4H-1 (+B3) - Body ground | Ignition switch off | 11 to 14 V |
| 4D-23 (+B4) - Body ground | Ignition switch off | 11 to 14 V |
| 4B-11 (IGR) - Body ground | Ignition switch ON | 11 to 14 V |
| 4C-17 (IGP) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure2
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A85 and A86 semiconductor power integration ECU connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A86)Location & Routingewd_type=routing;type=c;code=A86 Click Connector(A86)Engine Compartment>Engine Room Main Wire>Semiconductor Power Integration ECUewd_type=component;type=c;code=A86;pinno=26 |
||
| A86-26 (GND1) - Body ground | Always | Below 1 Ω |
Pre-procedure2
Connect the cable to the negative (-) auxiliary battery terminal.
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A85,A86)Location & Routingewd_type=routing;type=c,c;code=A85,A86 Click Connector(A85)Engine Compartment>Engine Room Main Wire>Semiconductor Power Integration ECUewd_type=component;type=c;code=A85;pinno=1 Click Connector(A86)Engine Compartment>Engine Room Main Wire>Semiconductor Power Integration ECUewd_type=component;type=c;code=A86;pinno=20 |
||
| A85-1 (+B) - Body ground | Ignition switch ON | 8 to 14 V |
| A86-20 (IG) - Body ground | Ignition switch ON | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4D power distribution box assembly connector.
Disconnect the A86 semiconductor power integration ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A86)Location & Routingewd_type=routing;type=c;code=A86 Click Connector(A86)Engine Compartment>Engine Room Main Wire>Semiconductor Power Integration ECUewd_type=component;type=c;code=A86;pinno=8 |
||
| A86-8 (CXPI) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A86-8 (CXPI) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A49 and A50 windshield wiper relay assembly connectors.
Procedure1
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A49)Location & Routingewd_type=routing;type=c;code=A49 Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assemblyewd_type=component;type=c;code=A49;pinno=5 |
||
| A49-5 (ES) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A50)Location & Routingewd_type=routing;type=c;code=A50 Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assemblyewd_type=component;type=c;code=A50;pinno=6,8 |
||
| A50-6 (IGWS) - Body ground | Ignition switch ON | 11 to 14 V |
| A50-8 (+B) - Body ground | Ignition switch ON or less than approximately 60 seconds after ignition switch turned off | 11 to 14 V |
| A50-8 (+B) - Body ground | Approximately 60 seconds or more after ignition switch turned off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A49 windshield wiper relay assembly connector.
Disconnect the 4D power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A49)Location & Routingewd_type=routing;type=c;code=A49 Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assemblyewd_type=component;type=c;code=A49;pinno=4 |
||
| A49-4 (MPX1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A49-4 (MPX1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A4 light control LED ECU LH connector.
Procedure1
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4)Location & Routingewd_type=routing;type=c;code=A4 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=5 |
||
| A4-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4)Location & Routingewd_type=routing;type=c;code=A4 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=2 |
||
| A4-2 (LO) - Body ground | Taillight on | 9.5 to 14 V |
| A4-2 (LO) - Body ground | Taillight off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A4 light control LED ECU LH connector.
Disconnect the 4D power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4)Location & Routingewd_type=routing;type=c;code=A4 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=1 |
||
| A4-1 (AT1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A4-1 (AT1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A5 light control LED ECU RH connector.
Procedure1
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5)Location & Routingewd_type=routing;type=c;code=A5 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=5 |
||
| A5-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5)Location & Routingewd_type=routing;type=c;code=A5 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=2 |
||
| A5-2 (LO) - Body ground | Taillight on | 9.5 to 14 V |
| A5-2 (LO) - Body ground | Taillight off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A5 light control LED ECU RH connector.
Disconnect the 4D power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5)Location & Routingewd_type=routing;type=c;code=A5 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=1 |
||
| A5-1 (AS1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A5-1 (AS1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG