Home › General › MAINTENANCE › FRONT DISC BRAKE PAD › 2020.08–2021.07
RM3700E _V1 General _093024 MAINTENANCE _0441778 FRONT DISC BRAKE PAD A

MAINTENANCE  FRONT DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C445648N02
3.25,3.917 4.417,5.583 1.167,1.667 0.156,2.344 1.49,3.76 1.333,1.417 4.177,3.042 4.667,3.042 false 2.021,1.302 2.542,1.302 true 1.75,4.177 1.75,4.76 false 4.417,5.177 4.885,5.177 false 6.375,0.281 6.781,0.281 false 1.75,4.417 2.583,4.417 false 0.844,3.75 0.844,4.104 false 4,2.906 4.281,3.26 0.281,0.354 18 false 3 1.823,1.167 2.021,1.5 0.198,0.333 18 true 4 1.677,4.792 1.958,5.146 0.281,0.354 18 false 5 5.146,5.052 5.427,5.406 0.281,0.354 18 false 6 0.906,4.135 1.188,4.49 0.281,0.354 18 false 6 5.063,0.146 5.271,0.458 0.208,0.313 18 true 1 5.667,0.146 6.01,0.469 0.344,0.323 18 true , 2 6.042,0.219 6.385,0.448 0.344,0.229 12 true (*A) 5.302,0.188 5.646,0.417 0.344,0.229 12 true (*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 FRONT WHEEL - - - -
4 FRONT DISC BRAKE CYLINDER ASSEMBLY - (Click here) - -
5 FRONT DISC BRAKE PAD - (Click here) - -
6 FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT - (Click here) - -

*A for HV Model - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC [C13CD00, C13CE00, C140000] may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 4.SEPARATE FRONT DISC BRAKE CYLINDER ASSEMBLY

Z101186

CAUTION:
C445649

·

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when removing the front disc brake pads.

·

After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.

·

The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.




a.
C445650N02
1.948,0.146 2.354,0.448 0.406,0.302 18 true i, ii

i.

Hold the front disc brake cylinder slide pin (lower side) and remove the bolt.

NOTICE:

Do not kink or damage the brake line.



ii.

Pull the front disc brake cylinder assembly upward.



Hide 5.REMOVE FRONT DISC BRAKE PAD

a.
C445651


Hide 6.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C445652N01
0.198,0.104 0.479,0.458 0.281,0.354 18 false i 3.844,0.156 4.125,0.51 0.281,0.354 18 false ii

i.

Remove the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim from each front disc brake pad.


ii.

Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake pad wear indicator plate from each front disc brake pad.