| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | AIR CONDITIONER UNIT ASSEMBLY | - | ( )
|
- | - |
| *A | w/ Headup Display | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | COOLER UNIT DRAIN HOSE GROMMET | 88539G | ( )
|
- | - |
| 10 | DRAIN COOLER HOSE | 88539J | - | - | - |
| 11 | NO. 4 DASH PANEL INSULATOR PAD | 55216C | ( )
|
- | - |
| 12 | FRONT FLOOR CARPET ASSEMBLY | 58510D | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | FRONT SEAT ASSEMBLY RH | - | - | - | - |
| 14 | FRONT SEAT ASSEMBLY LH | - | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 15 | NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY | 55084E | - | - | - |
| 16 | NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY | 55085 | - | - | - |
| 17 | NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY | 55086 | - | - | - |
| 18 | STEERING COLUMN ASSEMBLY | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 25 | OUTER COWL TOP PANEL SUB-ASSEMBLY | 55701J | - | - | - |
| 26 | NO. 1 FRONT VENTILATOR SEAL | 55815E | - | - | - |
| 27 | WATER GUARD PLATE LH | 55735A | - | - | - |
| 28 | WINDSHIELD WIPER MOTOR AND LINK | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
Install the 6 bolts.
| *a | Bolt A | *b | Bolt B |
|
Install in this Direction | - | - |
Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
Install the Bolt A and Bolt B.
Temporarily install the nut.
55306A
3.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *a | Bolt | *b | Screw |
| *c | Nut | - | - |
Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
4.INSTALL AIR CONDITIONER UNIT ASSEMBLY
Tighten the 3 bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.
82141
5.INSTALL INSTRUMENT PANEL WIRE
| *a | Guide | *b | Clamp |
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
6.INSTALL POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
7.INSTALL TELEMATICS TRANSCEIVER WITH BRACKET
83108
8.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
88539G
9.INSTALL COOLER UNIT DRAIN HOSE GROMMET
| *a | Lip | - | - |
Install a new cooler unit drain hose grommet.
If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.
88539J
10.INSTALL DRAIN COOLER HOSE
55216C
11.INSTALL NO. 4 DASH PANEL INSULATOR PAD
Install the No. 4 dash panel insulator pad.
Install 2 new clips as shown in the illustration.
58510D
12.INSTALL FRONT FLOOR CARPET ASSEMBLY
Install the front floor carpet assembly with the 2 clips as shown in the illustration.
13.INSTALL FRONT SEAT ASSEMBLY RH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION
14.INSTALL FRONT SEAT ASSEMBLY LH
Use the same procedure as for the RH side.
55084E
15.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY
55085
16.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
55086
17.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
18.INSTALL STEERING COLUMN ASSEMBLY
87211
19.INSTALL NO. 1 AIR DUCT
|
|
20.INSTALL INSTRUMENT PANEL ASSEMBLY
87245
21.INSTALL INLET HEATER WATER HOSE
| *A | for M15A-FXE | *B | for M15A-FKS |
| *a | View A | *b | Marking |
| *c | Clip Installation Angle (120°) | - | - |
for M15A-FXE:
1. Connect the inlet heater water hose with the marking (yellow) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
for M15A-FKS:
1. Connect the inlet heater water hose with the marking (yellow) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
16290F
22.INSTALL NO. 3 WATER BY-PASS HOSE ASSEMBLY
| *A | for M15A-FXE | *B | for M15A-FKS |
| *a | View A | *b | Marking |
| *c | Clip Installation Angle (120°) | - | - |
for M15A-FXE:
1. Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
for M15A-FKS:
1. Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
88710E
23.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the air conditioner tube and accessory assembly.
Apply sufficient compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.
for Gasoline Model:
ND-OIL 8 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the O-ring to the air conditioner tube and accessory assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the air conditioner tube and accessory assembly.
88707B
24.INSTALL SUCTION TUBE SUB-ASSEMBLY B
Remove the vinyl tape from the suction tube sub-assembly B.
Apply sufficient compressor oil to a new O-ring and fitting surface of the suction tube sub-assembly B.
for Gasoline Model:
ND-OIL 8 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the O-ring to the suction tube sub-assembly B.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction tube sub-assembly B.
Rotate the hook connector as shown in the illustration.
Install the bolt.
55701J
25.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55815E
26.INSTALL NO. 1 FRONT VENTILATOR SEAL
55735A
27.INSTALL WATER GUARD PLATE LH
28.INSTALL WINDSHIELD WIPER MOTOR AND LINK
29.ADD ENGINE COOLANT
for M15A-FKS:
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE COOLANT (for Engine)>REPLACEMENT
30.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
31.INSPECT FOR COOLANT LEAK
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION
for M15A-FXE:
Click hereEngine / Hybrid System>M15A-FXE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION
32. WARM UP ENGINE (for Gasoline Model)
33.WARM UP COMPRESSOR (for HV Model)
34.INSPECT FOR REFRIGERANT LEAK
53876A
35.INSTALL FRONT FENDER LINER LH
36. INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)