Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL VALVE (for Intake Side)
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442015 CAMSHAFT OIL CONTROL VALVE(for Intake Side) A

M15A-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE(for Intake Side)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472747N01
0.667,3.833 1.083,3.833 false 1.542,1.99 1.958,1.99 false 2.333,0.917 2.667,0.917 2.667,0.917 3.135,1.646 false 6.354,0.281 6.771,0.281 false 0.5,3.688 0.781,4.042 0.281,0.354 18 false 1 1.375,1.854 1.656,2.208 0.281,0.354 18 false 2 2.135,0.76 2.417,1.115 0.281,0.354 18 false 4 6.156,0.146 6.438,0.5 0.281,0.354 18 false 3 0.979,3.281 1.26,3.635 0.281,0.354 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ENGINE UNDER COVER RH 51441C - - -
2 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side) 15370 - - -
3 SET NO. 1 CYLINDER TO TDC/COMPRESSION - (Click here) - -
4 CAMSHAFT TIMING GEAR BOLT 135A0 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the intake camshaft timing gear bolt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of camshaft timing gear assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 51441C 1.REMOVE ENGINE UNDER COVER RH

Hide 15370 2.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A461557N01
2,0.063 2.281,0.417 0.281,0.354 18 false i 0.5,2.021 0.781,2.375 0.281,0.354 18 false ii 4.063,2.042 4.344,2.396 0.281,0.354 18 false ii

i.

Turn the crankshaft pulley clockwise until its timing mark (cutout) is aligned with the protrusion on the timing chain cover assembly as shown in the illustration.


ii.

Check that the cutout of the camshaft timing gear assembly is at the top.

HINT:

If the cutout of the camshaft timing gear assembly is not at the top, turn the crankshaft 360° clockwise and align the timing mark (cutout) of the crankshaft pulley with the protrusion on the timing chain cover assembly again.




Hide 135A0 4.REMOVE CAMSHAFT TIMING GEAR BOLT

Z101186

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

Do not turn the crankshaft pulley after removing the camshaft timing gear bolt.




a.
A461558N01
0.458,0.104 0.74,0.458 0.281,0.354 18 false i

i.

While holding the crankshaft pulley, remove the camshaft timing gear bolt.