Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 1) › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442028 AIR FUEL RATIO SENSOR(for Sensor 1) A

M15A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 1)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A476287N02
0.615,1.031 1.281,1.198 0.667,0.167 3.917,0.844 4.75,1.177 0.833,0.333 2.958,2.125 3.292,2.125 false 3.427,1.448 3.76,1.448 false 2.698,1.01 3.031,1.01 false 1.74,0.594 2.073,0.594 false 6.49,0.208 6.823,0.208 false 1.292,1.115 1.625,1.115 false 5.469,1.813 4.938,0.99 4.938,0.99 4.76,0.99 false 6.417,0.583 6.75,0.583 false 3.771,0.906 4.052,1.26 0.281,0.354 18 false 1 3.396,1.99 3.677,2.344 0.281,0.354 18 false 2 3.865,1.292 4.146,1.646 0.281,0.354 18 false 4 3.073,0.844 3.354,1.198 0.281,0.354 18 false 3 2.125,0.448 2.406,0.802 0.281,0.354 18 false 5 6.333,0.094 6.552,0.417 0.219,0.323 18 false 6 0.677,1.042 1.365,1.271 0.688,0.229 8 false 12 (122, 9) 1.469,0.865 1.927,1.063 0.458,0.198 10 false x12 4.01,0.865 4.719,1.073 0.708,0.208 8 false 44 (449, 32) 3.969,1 4.802,1.271 0.833,0.271 8 false 37.7 (384, 28)* 6.26,0.417 6.479,0.74 0.219,0.323 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AIR FUEL RATIO SENSOR 89467B (Click here) - -
2 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
3 NO. 1 FRONT VENTILATOR SEAL 55815E - - -
4 WATER GUARD PLATE LH 55735A - - -
5 WINDSHIELD WIPER MOTOR AND LINK - - - -
6 INSPECT FOR EXHAUST GAS LEAK - (Click here) - -
7 PERFORM INITIALIZATION - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR

a.
A458738C04
1.396,1.344 1.708,1.01 true 0.469,0.135 1.208,0.458 0.74,0.323 18 true i, ii, iii 1.188,1.354 1.51,1.521 0.323,0.167 10 true SST 4.323,1 4.635,1.198 0.313,0.198 10 false *a 5.281,1.031 5.594,1.229 0.313,0.198 10 false *b
*a SST Fulcrum Length *b Torque Wrench Fulcrum Length


i.

Using SST, install the air fuel ratio sensor to the exhaust manifold.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Engage the 2 clamps.


iii.

Connect the air fuel ratio sensor connector.



Hide 55701J 2.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55815E 3.INSTALL NO. 1 FRONT VENTILATOR SEAL

Hide 5.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 7.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION