Home › Engine / Hybrid System › M15A-FXE (COOLING) › THERMOSTAT
RM3700E _51 Engine / Hybrid System _093772 M15A-FXE COOLING _0442083 THERMOSTAT A

M15A-FXE COOLING  THERMOSTAT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A461091N01
6.375,0.271 6.708,0.271 false 3.833,2.104 3.833,2.438 false 2.531,4.083 2.865,4.083 false 3.292,2.708 3.292,3 false 1.49,2.688 1.823,2.688 false 1.208,2.208 1.375,2.208 1.375,2.208 1.99,1.781 false 1.708,1.156 1.875,1.156 1.875,1.156 3.063,1.771 false 2.844,0.76 3.177,0.76 false 6.198,0.146 6.479,0.5 0.281,0.354 18 false 2 3.771,2.479 4.052,2.833 0.281,0.354 10 false ● 2.375,3.948 2.656,4.302 0.281,0.354 18 false 1 4.146,5.24 4.417,5.417 0.271,0.177 10 false x4 5.104,5.531 5.375,5.708 0.271,0.177 10 false x4 5.885,5.323 6.156,5.5 0.271,0.177 10 false x9 3.385,3.01 3.667,3.365 0.281,0.354 18 false 6 1.313,2.563 1.594,2.917 0.281,0.354 18 false 4 1.021,2.063 1.302,2.417 0.281,0.354 18 false 5 1.542,1.021 1.823,1.375 0.281,0.354 18 false 7 2.75,1.281 3.021,1.458 0.271,0.177 10 false x2 2.667,0.635 2.948,0.99 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 DRAIN ENGINE COOLANT (for Engine) - - (Click here) -
3 INTAKE MANIFOLD 17111 - - -
4 NO. 2 RADIATOR HOSE 16572D - - -
5 BRACKET - (Click here) - -
6 NO. 6 WATER BY-PASS HOSE 16283 (Click here) - -
7 WATER INLET WITH THERMOSTAT SUB-ASSEMBLY 16031 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the water inlet with thermostat sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Cleaning the deposits from the throttle body with motor assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 16572D 4.DISCONNECT NO. 2 RADIATOR HOSE

a.
A461088


Hide 5.SEPARATE BRACKET

a.
A460658N01
2.167,0.865 2.333,1.177 0.167,0.313 18 true i 3.521,1.292 3.708,1.604 0.188,0.313 18 true ii

i.

Disconnect the engine water pump assembly (water inlet housing) connector.


ii.

Using an 8 mm socket wrench, remove the bolt and disconnect the bracket from the engine water pump assembly (water inlet housing).



Hide 16283 6.REMOVE NO. 6 WATER BY-PASS HOSE

a.
A460659N01
0.469,0.115 0.75,0.469 0.281,0.354 18 false i

i.

Slide the clip and disconnect the No. 6 water by-pass hose from the water inlet with thermostat sub-assembly.

NOTICE:
·

Do not apply force to the water inlet with thermostat sub-assembly when disconnecting the No. 6 water by-pass hose.

·

Do not damage the water inlet with thermostat sub-assembly.



HINT:

When disconnecting the No. 6 water by-pass hose, slide the clip, rotate the hose and pull it straight off the pipe.




Hide 16031 7.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

a.
A461090N01
1.042,0.104 1.594,0.458 0.552,0.354 18 false ii 5.583,0.104 5.75,0.385 0.167,0.281 18 true i

i.

Using an 8 mm socket wrench, remove the 2 bolts and water inlet with thermostat sub-assembly.


ii.

Remove the gasket from the water inlet with thermostat sub-assembly.