Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP › 2020.08–2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0442068 VACUUM PUMP A

BRAKE SYSTEM (OTHER)  VACUUM PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442522N02
4.49,4.146 4.792,4.146 false 4.646,5.021 5.021,5.021 false 6.167,3.583 6.5,3.583 false 5.208,1.375 5.542,1.375 false 1.385,1.281 1.719,1.281 false 3.604,4.823 3.604,5.156 false 3.563,5.156 3.719,5.354 0.156,0.198 10 false ● 5.198,5.385 5.438,5.583 0.24,0.198 10 false x3 5.323,4.865 5.563,5.229 0.24,0.365 18 false 5 5.073,4.01 5.313,4.375 0.24,0.365 18 false 2 6.552,3.438 6.792,3.802 0.24,0.365 18 false 3 4.677,2.802 4.917,3 0.24,0.198 10 false x4 5.594,1.24 5.833,1.604 0.24,0.365 18 false 4 1.76,1.146 2,1.51 0.24,0.365 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ECM 89661 - - -
2 NO. 1 VACUUM HOSE CONNECTOR 44777 (Click here) - -
3 FUEL TANK TO CANISTER TUBE 77261D - - -
4 ENGINE WIRE 82121 - - -
5 VACUUM PUMP ASSEMBLY 29300 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during vacuum pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 44777 2.DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

Z101186

NOTICE:

Be sure to disconnect the No. 1 vacuum hose connector by hand.



a.
C442523C02
6.198,0.906 5.885,1.292 5.885,1.292 6.188,1.125 true 5.698,1.24 6.01,1.396 0.313,0.156 10 false *a 0.323,0 0.604,0.354 0.281,0.354 18 false i
*a Retainer - -
V100135

Pinch
V113148

Pull off


i.

Pinch the retainer of the No. 1 vacuum hose connector, and then pull the No. 1 vacuum hose connector off of the vacuum pump assembly.



Hide 77261D 3.SEPARATE FUEL TANK TO CANISTER TUBE

a.
C429604


Hide 82121 4.SEPARATE ENGINE WIRE

a.
C429605


Hide 29300 5.REMOVE VACUUM PUMP ASSEMBLY

a.
C442524N02
0.313,0 0.552,0.25 0.24,0.25 18 true i 5.75,0.531 5.99,0.781 0.24,0.25 18 true ii

i.

Using an 8 mm socket wrench, remove the 3 bolts and vacuum pump assembly from the engine assembly.


ii.

Remove the No. 1 vacuum pump O-ring from the vacuum pump assembly.