Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.08–2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0442086 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B120687  P/W Master SW System Missing Message  B232187  D-Door P/W System Missing Message  B232287  P-Door P/W System Missing Message  B232387  RR-Door P/W System Missing Message  B232487  RL-Door P/W System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, power window regulator motor assembly (driver door), power window regulator motor assembly (front passenger door), power window regulator motor assembly (rear door RH) or power window regulator motor assembly (rear door LH) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B120687 P/W Master SW System Missing Message No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Wire harness or connector


Main Body A
B232187 D-Door P/W System Missing Message No communication between front power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly (driver door)

·

Wire harness or connector


Main Body A
B232287 P-Door P/W System Missing Message No communication between front power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (front passenger door)

·

Wire harness or connector


Main Body A
B232387 RR-Door P/W System Missing Message No communication between rear power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (rear RH door)

·

Wire harness or connector


Main Body A
B232487 RL-Door P/W System Missing Message No communication between rear power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (rear LH door)

·

Wire harness or connector


Main Body A

WIRING DIAGRAM

C434541E04
1.083,1.031 1.458,1.219 0.375,0.188 10 false LIN2 1.51,0.854 1.75,1.021 0.24,0.167 10 false 15 0.208,2.344 1.375,2.885 1.167,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.51,2.25 2.927,2.698 1.417,0.448 10 false Power Distribution Box Assembly 4.583,1.052 4.958,1.24 0.375,0.188 10 false LIN1 4.583,1.396 4.958,1.583 0.375,0.188 10 false LIN2 5.417,1.396 5.865,1.594 0.448,0.198 10 false GND 5.615,1.021 5.802,1.188 0.188,0.167 10 false B 4.365,1.927 5.948,2.313 1.583,0.385 10 false Multiplex Network Master Switch Assembly 5.99,1.177 6.885,1.375 0.896,0.198 10 false ECU-B NO. 2 4.417,0.208 5.792,0.417 1.375,0.208 10 false from Auxiliary Battery 4.594,2.896 4.969,3.083 0.375,0.188 10 false LIN 5.625,2.698 5.813,2.865 0.188,0.167 10 false B 5.448,3.073 5.802,3.271 0.354,0.198 10 false GND 6.073,2.844 6.823,3.052 0.75,0.208 10 false DOOR F/R 4.219,3.594 6.135,3.969 1.917,0.375 10 false Front Power Window Regulator Motor Assembly (Driver Door) 4.604,4.542 4.979,4.729 0.375,0.188 10 false LIN 5.625,4.365 5.813,4.531 0.188,0.167 10 false B 5.438,4.729 5.792,4.927 0.354,0.198 10 false GND 6.104,4.5 6.854,4.708 0.75,0.208 10 false DOOR F/L 4.073,5.229 6.365,5.615 2.292,0.385 10 false Front Power Window Regulator Motor Assembly (Front Passenger Door) 4.594,6.188 4.969,6.375 0.375,0.188 10 false LIN 5.646,5.99 5.833,6.156 0.188,0.167 10 false B 5.438,6.365 5.792,6.563 0.354,0.198 10 false GND 6.104,6.156 6.854,6.365 0.75,0.208 10 false DOOR R/R 4.094,6.906 6.385,7.292 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear RH Door) 4.583,7.854 4.958,8.042 0.375,0.188 10 false LIN 5.625,7.688 5.813,7.854 0.188,0.167 10 false B 5.438,8.042 5.792,8.24 0.354,0.198 10 false GND 6.115,7.833 6.823,8.021 0.708,0.188 10 false DOOR R/L 4.104,8.552 6.396,8.938 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear LH Door) 0.625,9.521 2.281,9.719 1.656,0.198 10 false : LIN Communication Line 1.49,1.042 1.729,1.208 0.24,0.167 10 false MB 2.75,0.844 2.99,1.01 0.24,0.167 10 false 17 2.74,1.042 2.979,1.208 0.24,0.167 10 false 4E 4.344,0.896 4.583,1.063 0.24,0.167 10 false 17 4.333,1.25 4.573,1.417 0.24,0.167 10 false 16 5.823,0.948 6.063,1.115 0.24,0.167 10 false 11 5.823,1.302 6.063,1.469 0.24,0.167 10 false 12 4.365,1.74 4.656,1.906 0.292,0.167 10 false K5 4.417,2.729 4.656,2.896 0.24,0.167 10 false 9 5.833,2.594 6.073,2.76 0.24,0.167 10 false 2 5.844,2.958 6.083,3.125 0.24,0.167 10 false 1 4.219,3.406 4.594,3.594 0.375,0.188 10 false K7 4.406,4.396 4.646,4.563 0.24,0.167 10 false 9 5.844,4.26 6.083,4.427 0.24,0.167 10 false 2 5.823,4.604 6.063,4.771 0.24,0.167 10 false 1 4.083,5.042 4.458,5.229 0.375,0.188 10 false L7 4.427,6.01 4.667,6.177 0.24,0.167 10 false 9 5.844,5.927 6.083,6.094 0.24,0.167 10 false 2 5.823,6.26 6.063,6.427 0.24,0.167 10 false 1 4.094,6.698 4.469,6.885 0.375,0.188 10 false M4 4.417,7.698 4.656,7.865 0.24,0.167 10 false 9 5.854,7.594 6.094,7.76 0.24,0.167 10 false 2 5.844,7.927 6.083,8.094 0.24,0.167 10 false 1 4.094,8.385 4.469,8.573 0.375,0.188 10 false N4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
B232588 is output A
B120687, B232187, B232287, B232387 and B232487 are output B
B120687 and B232187 are output C
Only B120687 is output D
Only B232187 is output E
Only B232287 is output F
Only B232387 is output G
Only B232487 is output H
DTCs are not output I



A

B

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

D

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

E

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

F

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))

G

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))

H

14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

I

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition Output DTC

Click Location & Routing(K5)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

4E-17 - K5-17 (LIN1) Always Below 1 Ω B120687,B232187,B232287,B232387,B232487


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

Pre-procedure1

a.

Remove the power distribution box assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


C449238C02
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.229,0.927 2.427,1.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.958,0.375 2.271,0.531 0.313,0.156 10 false MB 5.615,0.125 5.927,0.281 0.313,0.156 10 false 4E 2.344,1.417 2.76,1.594 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Output DTC
4E-17 - MB-15 (LIN2) Always Below 1 Ω B120687,B232187,B232287,B232387,B232487


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K5)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

4E-17 - K5-17 (LIN1) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K5)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

K5-11 (B) - K5-12 (GND) Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K5)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

K5-12 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

4E-17 - K7-9 (LIN) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K7-2 (B) - K7-1 (GND) Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K7-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

4E-17 - K7-9 (LIN) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L7)Location & Routing

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

4E-17 - L7-9 (LIN) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


Procedure1

a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L7)Location & Routing

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L7-2 (B) - L7-1 (GND) Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L7)Location & Routing

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L7-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

4E-17 - M4-9 (LIN) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


Procedure1

a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

M4-2 (B) - M4-1 (GND) Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

M4-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(N4)Location & Routing

Click Connector(N4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

4E-17 - N4-9 (LIN) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

15.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(N4)Location & Routing

Click Connector(N4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

N4-2 (B) - N4-1 (GND) Ignition switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N4)Location & Routing

Click Connector(N4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

N4-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR