Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P0BF528  Drive Motor "B" Phase V Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure  P0BF928  Drive Motor "B" Phase W Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure  P31E41F  Drive Motor "B" Phase V Current Sensor Circuit Intermittent  P31E51F  Drive Motor "B" Phase W Current Sensor Circuit Intermittent  P33C028  Drive Motor "B" Phase V Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure  P33C528  Drive Motor "B" Phase W Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure  P33D862  Drive Motor "B" Phase V Current Sensor Signal Compare Failure  P33D962  Drive Motor "B" Phase W Current Sensor Signal Compare Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate that the current sensor value is abnormal. The cause of this malfunction may be one of the following:


Rear inverter internal malfunction
·

Current sensor malfunction

·

Inverter internal circuit malfunction


DESCRIPTION

The rear motor generator control ECU, which is built into the rear inverter assembly, monitors the inverter current sensor. These DTCs indicate the malfunction of inverter current sensors and do not indicate a malfunction of the high-voltage system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0BF528 Drive Motor "B" Phase V Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure Rear motor inverter current sensor V phase "Ach" offset malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0BF928 Drive Motor "B" Phase W Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure Rear motor inverter current sensor W phase "Ach" offset malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P31E41F Drive Motor "B" Phase V Current Sensor Circuit Intermittent Abnormal deviation of phase W detected in rear motor inverter current sensor when P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P31E51F Drive Motor "B" Phase W Current Sensor Circuit Intermittent Abnormal deviation of phase V detected in rear motor inverter current sensor when P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P33C028 Drive Motor "B" Phase V Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure Rear motor inverter current sensor V phase "Bch" offset malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P33C528 Drive Motor "B" Phase W Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure Rear motor inverter current sensor W phase "Bch" offset malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P33D862 Drive Motor "B" Phase V Current Sensor Signal Compare Failure Rear motor inverter current sensor V phase deviation malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P33D962 Drive Motor "B" Phase W Current Sensor Signal Compare Failure Rear motor inverter current sensor W phase deviation malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

5.

With the vehicle stopped, begin moving with the accelerator opening angle between 20% to 50% and a speed of approximately 10 km/h (6 mph), then stop the vehicle and repeat the same procedure several times.

While doing this, check that the "Rear motor torque" value does not remain at 0 N*m continuously, but rather changes to indicate that the rear motor is operating.

HINT:

Unless rear motor torque is restricted due to DTC output, the rear motor torque will not remain at 0 N*m continuously.


6.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

7.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
Only P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 for Rear motor generator control system is output A
P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 is output and DTCs other than the DTCs in the table below are output B
P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 is output and Insulation malfunction of Hybrid control system DTCs in the table below are output C
P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 is output and Microcomputer malfunction of Motor generator control system DTCs in the table below are output D
P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 is output and Microcomputer malfunction of Rear motor generator control system DTCs in the table below are output E
P0BF528, P0BF928, P31E41F, P31E51F, P33C028, P33C528, P33D862 or P33D962 is output and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output F


Table 1
Malfunction Content System Relevant DTC
Insulation malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1C8049 Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure

Table 2
Malfunction Content System Relevant DTC
Microcomputer malfunction Motor generator control system P0A1C49 Drive Motor B" Control Module Internal Electronic Failure"
P314887 Lost Communication between Drive Motor A" and "B" Missing Message"
Rear motor generator control system P1C2C1C Drive Motor B" Control Module AD Converter Circuit Voltage Out of Range
P1C2C49 Drive Motor B" Control Module AD Converter Circuit Internal Electronic Failure
P314987 Lost Communication between Drive Motor A" and "B" Missing Message
Power source circuit malfunction Rear motor generator control system P06B31C Drive Motor B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
P262C1C Drive Motor B" Control Module Offset Power Circuit Voltage Out of Range

HINT:

P0BF528, P0BF928, P33C028, P31E41F, P31E51F, P33C528, P33D862 or P33D962 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

C

D

E

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

F

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR