The Variable Valve Timing (VVT) system (for exhaust camshaft) adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller (camshaft timing exhaust gear assembly) to adjust the valve timing.
The cam timing oil control solenoid assembly operates according to signals received from the ECM to control the position of the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) and supply engine oil. The camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) moves when the ECM applies 12 V to the cam timing oil control solenoid assembly. The ECM changes the energizing time of the cam timing oil control solenoid assembly (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P001313 | Camshaft Position "B" - Actuator Bank 1 Circuit Open | Open or short in cam timing oil control solenoid assembly (for exhaust camshaft) circuit (1 trip detection logic). | ·
Open or short in cam timing oil control solenoid assembly (for exhaust camshaft) circuit ·
Cam timing oil control solenoid assembly (for exhaust camshaft) ·
ECM |
Comes on | Engine | A | SAE: P0013 |
This DTC is designed to detect an open or short in the cam timing oil control solenoid assembly circuit. If the cam timing oil control solenoid assembly duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store this DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Wait 5 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P001313.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Pre-procedure1
None.
Procedure1
Clear the DTC after recording the Freeze Frame Data and DTC.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Start the engine.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P001313 is output | B |
Post-procedure1
None.
A
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the cam timing oil control solenoid assembly (for exhaust camshaft) connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D17,D51)Location & Routingewd_type=routing;type=c,c;code=D17,D51 Click Connector(D17)Engine Compartment>Engine Wire>Cam Timing Oil Control Solenoid Assembly (Exhaust Side)ewd_type=component;type=c;code=D17;pinno=2,1 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=25,24 |
||
| D17-2 (+) - D51-25 (OE1+) | Always | Below 1 Ω |
| D17-1 (-) - D51-24 (OE1-) | Always | Below 1 Ω |
| D17-2 (+) or D51-25 (OE1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| D17-1 (-) or D51-24 (OE1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG