The D-4 system has two fuel injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The ECM determines which fuel injection system to use in accordance with the engine conditions. The injection system uses an injector driver (EDU) built into the ECM to rapidly operate the fuel injector assemblies. It converts injection request signals from the ECM to high-voltage and high-current injector-drive signals that drive the fuel injector assemblies.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P020113 | Cylinder 1 Injector "A" Circuit Open | One of following conditions is met (1 trip detection logic):
·
Short to +B in fuel injector assembly (No. 1 cylinder) circuit for 20 times or more. ·
Open or short to ground in fuel injector assembly (No. 1 cylinder) circuit for 20 times or more. ·
Fuel injector assembly (No. 1 cylinder) circuit current reaches the high limit for 20 times or more. |
·
Open or short in fuel injector assembly (No. 1 cylinder) circuit ·
Fuel injector assembly (No. 1 cylinder) ·
D INJ relay ·
ECM |
Comes on | Engine | A | SAE: P0201 |
| P020213 | Cylinder 2 Injector "A" Circuit Open | One of following conditions is met (1 trip detection logic):
·
Short to +B in fuel injector assembly (No. 2 cylinder) circuit for 20 times or more. ·
Open or short to ground in fuel injector assembly (No. 2 cylinder) circuit for 20 times or more. ·
Fuel injector assembly (No. 2 cylinder) circuit current reaches the high limit for 20 times or more. |
·
Open or short in fuel injector assembly (No. 2 cylinder) circuit ·
Fuel injector assembly (No. 2 cylinder) ·
D INJ relay ·
ECM |
Comes on | Engine | A | SAE: P0202 |
| P020313 | Cylinder 3 Injector "A" Circuit Open | One of following conditions is met (1 trip detection logic):
·
Short to +B in fuel injector assembly (No. 3 cylinder) circuit for 20 times or more. ·
Open or short to ground in fuel injector assembly (No. 3 cylinder) circuit for 20 times or more. ·
Fuel injector assembly (No. 3 cylinder) circuit current reaches the high limit for 20 times or more. |
·
Open or short in fuel injector assembly (No. 3 cylinder) circuit ·
Fuel injector assembly (No. 3 cylinder) ·
D INJ relay ·
ECM |
Comes on | Engine | A | SAE: P0203 |
| P062D13 | Fuel Injector Driver Circuit Performance Bank 1 Circuit Open | Open or short in fuel injector assembly (all cylinders) circuits for 30 times or more (1 trip detection logic). | ·
Open or short in fuel injector assembly circuit ·
Fuel injector assembly ·
D INJ relay ·
ECM |
Comes on | Engine | A | SAE: P062D |
The fuel injection sequence occurs in numerical order from No. 1 to No. 3.
The ECM monitors the Injector Driver (EDU) at all times. If drivers or fuel injector assembly is malfunctioning, the EDU sends fuel injector assembly operation condition signals (fail signals) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate D INJ relay, and illuminates the MIL.
| Required Sensors/Components | Fuel injector assembly
ECM (injector driver) |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine [A].
Idle the engine for 15 seconds or more [B].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P020113, P020213, P020313 or P062D13.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the current from the D INJ relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P020113, P020213, P020313 and P062D13 are output | A |
| P062D13 is output | B |
| P020113, P020213 or P020313 is output | C |
A
B
C
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | D INJ Relay |
Pre-procedure1
Remove the D INJ relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (D INJ relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | D INJ Relay |
Pre-procedure1
Remove the D INJ relay from the No. 1 engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (D INJ relay) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the INJ relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54)Location & Routingewd_type=routing;type=c;code=A54 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=53,34 |
||
| 5 (D INJ relay) - A54-53 (+BD1) | Always | Below 1 Ω |
| 2 (D INJ relay) - A54-34 (IREL) | Always | Below 1 Ω |
| 5 (D INJ relay) or A54-53 (+BD1) - Body ground and other terminals | Always | 10 kΩ or higher |
| 2 (D INJ relay) or A54-34 (IREL) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D51)Location & Routingewd_type=routing;type=c;code=D51 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=16,17,11,10,13,14 |
||
| D51-16 (#1D+) - D51-17 (#1D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| D51-11 (#2D+) - D51-10 (#2D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| D51-13 (#3D+) - D51-14 (#3D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| D51-16 (#1D+) or D51-17 (#1D-) - Body ground and other terminals | Always | 1 MΩ or higher |
| D51-11 (#2D+) or D51-10 (#2D-) - Body ground and other terminals | Always | 1 MΩ or higher |
| D51-13 (#3D+) or D51-14 (#3D-) - Body ground and other terminals | Always | 1 MΩ or higher |
The standard values shown are fuel injector assembly resistance values.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION