Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P03351F  Crankshaft Position Sensor "A" Circuit Intermittent  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

Refer to DTC P033511.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P033511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P03351F Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


- Engine A SAE: P0339
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range No crankshaft position sensor signal to the ECM while cranking (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


Comes on Engine A SAE: P0335
P033531 Crankshaft Position Sensor "A" No Signal The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


Comes on Engine A SAE: P0335

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P033511


MONITOR DESCRIPTION

A DTC will be stored if any of the following occurs:

·

The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is being cranked.

·

The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is running.

·

The engine stalls and the engine speed signal value decreases rapidly (under normal conditions the engine speed will decrease gradually).


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more [A].

8.

Run the engine at an engine speed of 1000 rpm for 5 seconds or more [B].

9.

Turn the GTS on.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P03351F, P03352A or P033531.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

(e)

Start the engine.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)

Pre-procedure1

a.

Start the engine.


Procedure1

a.

Read the values displayed on the GTS while the engine is running.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(e4)Location & Routing

Click Connector(e4)Engine Compartment>Sensor Wire>Crank Position Sensor

e4-3 (VCNE) - Body ground Ignition switch ON 4.5 to 5.5 V
e4-1 (NE+) - Body ground Ignition switch ON 3.0 to 5.0 V



b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(e4)Location & Routing

Click Connector(e4)Engine Compartment>Sensor Wire>Crank Position Sensor

e4-3 (VCNE) - e4-1 (NE+) Ignition switch off 1.425 to 1.575 kΩ
e4-2 (NE-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CRANKSHAFT POSITION SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CRANKSHAFT POSITION SENSOR)

Pre-procedure1

a.

None.


Procedure1

a.
B319222C07
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


Visually check the crankshaft position sensor for damage.


b.

Check the crankshaft position sensor installation condition.

OK:

The crankshaft position sensor does not have any damage and is installed properly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.INSPECT CRANKSHAFT POSITION SENSOR PLATE (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)

NG

4.INSPECT CRANKSHAFT POSITION SENSOR PLATE (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)
a.

Inspect the teeth of the crankshaft position sensor plate.

OK:

Crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(e4,D51)Location & Routing

Click Connector(e4)Engine Compartment>Sensor Wire>Crank Position Sensor

Click Connector(D51)Engine Compartment>Engine Wire>ECM

e4-3 (VCNE) - D51-116 (VCNE) Always Below 1 Ω
e4-2 (NE-) - D51-115 (NE-) Always Below 1 Ω
e4-1 (NE+) - D51-92 (NE+) Always Below 1 Ω
e4-3 (VCNE) or D51-116 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
e4-2 (NE-) or D51-115 (NE-) - Body ground and other terminals Always 10 kΩ or higher
e4-1 (NE+) or D51-92 (NE+) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR