Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  U010187  Lost Communication with TCM Missing Message  


MONITOR DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communication with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine speed, required engine torque, warning indicators in the combination meter assembly, DTCs and other data. The ECM sends signals to the TCM concerning engine speed, opening angle of the throttle valve, temperature of intake air, temperature of engine coolant, engine torque and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN communication system, illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
U010187 Lost Communication with TCM Missing Message All of the following conditions are met for 1.25 seconds or more (1 trip detection logic):
·

Ignition switch ON

·

Battery voltage is 10 V or higher

·

No communication between engine control unit and transmission control unit


·

ECM to TCM circuit

·

TCM

·

ECM


Comes on Engine B SAE: U0101

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: U010187.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A459383E01
0.406,0.292 0.719,0.49 0.313,0.198 10 false *1 3.427,0.323 3.74,0.521 0.313,0.198 10 false *1 0.448,1.583 0.76,1.781 0.313,0.198 10 false *2 3.385,1.563 3.698,1.76 0.313,0.198 10 false *2 1.51,0.188 1.781,0.375 0.271,0.188 10 false 6 2.844,0.198 3.115,0.385 0.271,0.188 10 false 24 1.719,0.354 2.031,0.552 0.313,0.198 10 false +B 2.417,0.354 2.823,0.531 0.406,0.177 10 false IGPD 1.354,0.719 3.198,1.104 1.844,0.385 10 false Certification ECU (Smart Key ECU Assembly)*1 0.719,1.854 1.125,2.031 0.406,0.177 10 false AM1 0.552,3.229 1.688,3.406 1.135,0.177 10 false BATT-MAIN NO.1 0.573,5.125 1.125,5.323 0.552,0.198 10 false Battery 1.51,1.583 1.781,1.771 0.271,0.188 10 false 7 1.708,1.583 2.115,1.76 0.406,0.177 10 false AM1 2.51,1.583 2.875,1.75 0.365,0.167 10 false IG1 2.823,1.583 3.094,1.771 0.271,0.188 10 false 8 1.469,2.063 1.823,2.25 0.354,0.188 10 false H54 1.438,2.25 4.031,2.479 2.594,0.229 10 false Ignition Switch Assembly*2 2.854,3.688 3.26,3.865 0.406,0.177 10 false IGP 4.073,3.219 5.156,3.5 1.083,0.281 10 false ECU-IGP NO.1 1.719,4.552 2.698,4.781 0.979,0.229 10 false EFI-MAIN NO.1 3.052,5.094 4.042,5.292 0.99,0.198 10 false EFI-MAIN NO.1 5.875,3.823 6.146,4.01 0.271,0.188 10 false 9 5.823,4.281 6.094,4.469 0.271,0.188 10 false 35 5.823,4.729 6.094,4.917 0.271,0.188 10 false 15 5.823,5.302 6.094,5.49 0.271,0.188 10 false 10 6.063,3.885 6.375,4.083 0.313,0.198 10 false +B 6.063,4.344 6.385,4.542 0.323,0.198 10 false +B2 6.073,4.729 6.531,4.917 0.458,0.188 10 false MREL 6.083,5.333 6.396,5.531 0.313,0.198 10 false E1 6.365,5.844 6.719,6.031 0.354,0.188 10 false A54 6.344,6.021 6.76,6.24 0.417,0.219 10 false ECM 1.448,5.615 4.302,5.823 2.854,0.208 10 false *1: w/ Entry and Start System 1.448,5.917 4.302,6.125 2.854,0.208 10 false *2: w/o Entry and Start System 2.833,0.385 3.292,0.583 0.458,0.198 10 false H45 1.365,0.385 1.823,0.583 0.458,0.198 10 false H46 0.677,0.531 1.135,0.729 0.458,0.198 10 false AM2 0.427,2.531 2.573,2.729 2.146,0.198 10 false INP STP NO.1-3 1.927,3.229 3.156,3.427 1.229,0.198 10 false IGP-MAIN 2.563,2.979 2.719,3.177 0.156,0.198 10 false 3 3.271,2.979 3.427,3.177 0.156,0.198 10 false 5 2.573,3.313 2.729,3.51 0.156,0.198 10 false 2 3.26,3.313 3.417,3.51 0.156,0.198 10 false 1 3.063,4.302 3.219,4.5 0.156,0.198 10 false 5 3.792,4.302 3.948,4.5 0.156,0.198 10 false 3 3.052,4.729 3.208,4.927 0.156,0.198 10 false 2 3.781,4.729 3.938,4.927 0.156,0.198 10 false 1 6.063,0.615 6.677,0.813 0.615,0.198 10 false CANP 6.073,1.01 6.688,1.208 0.615,0.198 10 false CANN 4.542,0.604 5.156,0.802 0.615,0.198 10 false CAN+ 4.542,0.99 5,1.188 0.458,0.198 10 false CAN- 4.979,0.448 5.292,0.646 0.313,0.198 10 false 18 4.99,0.854 5.302,1.052 0.313,0.198 10 false 17 5.885,0.458 6.198,0.656 0.313,0.198 10 false 7 5.844,0.844 6.156,1.042 0.313,0.198 10 false 17 4.729,1.667 5.042,1.865 0.313,0.198 10 false +B 4.979,1.563 5.135,1.76 0.156,0.198 10 false 1 5,1.813 6.229,2.01 1.229,0.198 10 false EFI NO.5 4.375,2.615 5.656,2.917 1.281,0.302 10 false TCM 4.385,2.458 4.844,2.656 0.458,0.198 10 false D71 4.177,1.719 4.49,1.917 0.313,0.198 10 false E1 3.99,1.625 4.146,1.823 0.156,0.198 10 false 2 4.5,2.177 5.115,2.375 0.615,0.198 10 false IGSW 4.979,2.094 5.292,2.292 0.313,0.198 10 false 41 1.573,6.24 4.427,6.448 2.854,0.208 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U010187)
a.

Perform the Health Check using the GTS.


b.

Read the DTCs.

Result:
Result Proceed to
U010187 and other DTCs are output A
U010187 is output B


HINT:

If any DTCs other than U010187 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

Pre-procedure1

a.

Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-1 (+B) - D71-2 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

Pre-procedure1

a.

Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-41 (IGSW) - D71-2 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGP RELAY - TCM)

4.CHECK HARNESS AND CONNECTOR (TCM - ECM)

Pre-procedure1

a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71,A54)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

D71-18 (CAN+) - A54-7 (CANP) Always Below 1 Ω
D71-17 (CAN-) - A54-17 (CANN) Always Below 1 Ω
D71-18 (CAN+) or A54-7 (CANP) - Body ground and other terminals Always 10 kΩ or higher
D71-17 (CAN-) or A54-17 (CANN) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC U010187)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC U010187)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
U010187 is output B



Post-procedure1

a.

None.



A

END

B