Refer to DTC P001001.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P001001
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P136411 | "C" Camshaft Position Actuator Bank 1 Circuit Short to Ground | While engine is running, short in VTM terminal of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic). | ·
Cam timing control motor with EDU assembly ·
Short in cam timing control motor with EDU assembly circuit ·
VVT relay ·
ECM |
Comes on | Engine | A | SAE Code: P1364 |
| P136415 | "C" Camshaft Position Actuator Bank 1 Circuit Short to Battery or Open | While engine is running, open or short in VTM and VTP terminals of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic). | ·
Cam timing control motor with EDU assembly ·
Open or short in cam timing control motor with EDU assembly circuit ·
VVT relay ·
ECM |
Comes on | Engine | A | SAE Code: P1364 |
These DTCs are stored when a power supply malfunction, diagnostic signal malfunction or motor operation signal malfunction is detected in the cam timing control motor with EDU assembly. The cam timing control motor with EDU assembly is equipped with a self-diagnostic function, which is used to send diagnostic a signal (VTM) to the ECM. If the ECM receives a VTP or VTM open or short signal, a DTC is output immediately (1 trip detection logic).
| Required sensors/Components | Cam timing control motor with EDU assembly |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine [A].
Idle the engine for 10 seconds or more [B].
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P136411 or P136415.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Refer to DTC P136001.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P136001
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Pre-procedure1
Disconnect the cam timing control motor with EDU assembly connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D15)Location & Routingewd_type=routing;type=c;code=D15 Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assemblyewd_type=component;type=c;code=D15;pinno=2 |
||
| D15-2 (VB1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the cam timing control motor with EDU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D15)Location & Routingewd_type=routing;type=c;code=D15 Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assemblyewd_type=component;type=c;code=D15;pinno=3 |
||
| D15-3 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Check installation condition.
Check that the 3 installation bolts of the cam timing control motor with EDU assembly are tightened to the specified torque.
| Item | Specified Condition |
|---|---|
| Torque | 21 N*m
214 kgf*cm 15 ft.*lbf |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the cam timing control motor with EDU assembly connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D15,D52)Location & Routingewd_type=routing;type=c,c;code=D15,D52 Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assemblyewd_type=component;type=c;code=D15;pinno=4,1 Click Connector(D52)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D52;pinno=44,45 |
||
| D15-4 (VTM) - D52-44 (EMD1) | Always | Below 1 Ω |
| D15-1 (VTP) - D52-45 (EDT1) | Always | Below 1 Ω |
| D15-4 (VTM) or D52-44 (EMD1) - Body ground and other terminals | Always | 10 kΩ or higher |
| D15-1 (VTP) or D52-45 (EDT1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P136411 or P136415 is output | B |
Post-procedure1
None.
A
B
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the VVT relay from the No. 1 engine room relay block.
Disconnect the cam timing control motor with EDU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D15)Location & Routingewd_type=routing;type=c;code=D15 Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assemblyewd_type=component;type=c;code=D15;pinno=2 |
||
| 3 (VVT relay) - D15-2 (VB1) | Always | Below 1 Ω |
| 3 (VVT relay) or D15-2 (VB1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the VVT relay from the No. 1 engine room relay block.
Procedure1
| *1 | No. 1 Engine Room Relay Block |
| *2 | VVT Relay |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (VVT relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the VVT relay from the No. 1 engine room relay block.
Turn the ignition switch to ON.
Procedure1
| *1 | No. 1 Engine Room Relay Block |
| *2 | VVT Relay |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (VVT relay) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG