Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443935 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B592961N01
6.5,0.271 6.833,0.271 false 6.448,0.594 6.781,0.594 false 5.771,3.313 5.771,2.979 false 6.323,0.135 6.604,0.49 0.281,0.354 18 false 1 6.271,0.458 6.552,0.813 0.281,0.354 18 false 2 5.813,3.313 6.094,3.667 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 HORN BUTTON ASSEMBLY 45130 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Z101186

CAUTION:
B417753

·

When storing the horn button assembly, keep the airbag deployment side facing upward.


·

If the airbag deploys for any reason, it may cause a serious accident.




a.
B596997C01
1.677,0.802 0.677,0.802 true 0.5,0.708 0.813,0.865 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 0.354,1.771 0.729,2.01 0.375,0.24 12 false *A 2.729,1.813 3.104,2.052 0.375,0.24 12 false *B
*A w/ Smart Entry and Start System *B w/o Smart Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592962C01
1.51,1.333 0.979,0.958 true 4.76,1.01 4.229,0.75 true 0.688,4.49 1.146,4.063 true 1.063,2.729 1.615,2.313 true 6.125,2.771 6.448,2.427 true 6.01,4.729 6.375,5.219 true 0.771,1.25 1.063,1.594 true 0.458,0.917 0.917,0.729 true 0.542,4.76 0.885,5.396 true 1.25,4.656 1.531,5.344 true 4.052,1.531 4.417,1.26 true 4.198,1.031 3.906,1.198 true 0.26,0.167 0.51,0.396 0.25,0.229 10 true *a 2.094,0.156 2.344,0.385 0.25,0.229 10 true *b 3.781,0.156 4.031,0.385 0.25,0.229 10 true *a 5.677,0.135 5.927,0.365 0.25,0.229 10 true *b 1.563,1.25 1.813,1.479 0.25,0.229 10 true *c 6.385,2.229 6.635,2.458 0.25,0.229 10 true *c 6.396,5.229 6.646,5.458 0.25,0.229 10 true *c 0.302,1.938 0.552,2.167 0.25,0.229 10 true *f 2.688,3.271 2.938,3.5 0.25,0.229 10 true *f 3.104,3.583 3.354,3.813 0.25,0.229 10 true *h 4.427,3.313 4.677,3.542 0.25,0.229 10 true *g 5.198,1.948 5.438,2.177 0.24,0.229 10 true *g 4.906,3.969 5.156,4.198 0.25,0.229 10 true *h 2.5,4.021 2.75,4.25 0.25,0.229 10 true *b 0.271,4.021 0.521,4.25 0.25,0.229 10 true *a 0.844,5.406 1.094,5.604 0.25,0.198 10 true *e 1.125,3.958 1.375,4.188 0.25,0.229 10 true *c 1.042,1.573 1.292,1.802 0.25,0.229 10 true *e 3.927,1.51 4.177,1.74 0.25,0.229 10 true *e 4.792,0.927 5.042,1.156 0.25,0.229 10 true *d 0.26,0.844 0.51,1.073 0.25,0.229 10 true *d 1.635,2.177 1.885,2.406 0.25,0.229 10 true *c 1.531,5.354 1.781,5.583 0.25,0.229 10 true *d 3.698,1.135 3.948,1.365 0.25,0.229 10 true *c 2.615,1.823 2.896,2.177 0.281,0.354 18 false i
*a Lock Position *b Unlock Position
*c Torsion Spring *d Pin
*e Protective Tape *f View A
*g View B *h View C


i.

Using a screwdriver, push in the torsion springs to disengage the pins as shown in the illustration.

NOTICE:

Do not drop the horn button assembly.




c.
B592963N01
4.146,1.458 4.427,1.781 0.281,0.323 18 false i 3.219,1.104 3.5,1.427 0.281,0.323 18 false ii 3.896,0.917 4.177,1.24 0.281,0.323 18 false iii 3.26,0.844 3.542,1.167 0.281,0.323 18 false iv

i.

Tilt the horn button assembly toward the seat and support it with one hand.

NOTICE:

When disconnecting the horn button assembly, do not pull the airbag wire harness.



ii.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iii.

Using a screwdriver with its tip wrapped with protective tape, release the lock and remove the wire harness clamp.


iv.

Disconnect the horn connector.