Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443939 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B592975N01
6.51,0.25 6.844,0.25 false 6.448,0.594 6.781,0.594 false 5.021,1.896 5.354,1.896 false 6.042,3.365 6.375,3.365 false 3.354,2.51 3.688,2.51 false 5.083,2.323 5.417,2.323 false 6.344,0.115 6.625,0.469 0.281,0.354 18 false 1 6.292,0.458 6.573,0.813 0.281,0.354 18 false 2 6.417,3.229 6.698,3.583 0.281,0.354 18 false 3 5.646,1.76 5.927,2.115 0.281,0.354 18 false 4 3.823,2.417 4.135,2.615 0.313,0.198 10 false *1 3.719,2.406 3.875,2.604 0.156,0.198 10 false ● 5.448,2.229 5.604,2.427 0.156,0.198 10 false ● 4.865,2.417 5.177,2.615 0.313,0.198 10 false x4 3.156,2.563 3.469,2.76 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 ROOF HEADLINING ASSEMBLY 63310 - - -
4 CURTAIN SHIELD AIR BAG ASSEMBLY 62170A (Click here) - -

*1 ROOF SIDE INNER GARNISH CLIP - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 63310 3.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62170A 4.REMOVE CURTAIN SHIELD AIR BAG ASSEMBLY

Z101186

CAUTION:
B585003

·

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


·

If the airbag deploys for any reason, it may cause a serious accident.




a.
B596997C01
1.677,0.802 0.677,0.802 true 0.5,0.708 0.813,0.865 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 0.354,1.771 0.729,2.01 0.375,0.24 12 false *A 2.729,1.813 3.104,2.052 0.375,0.24 12 false *B
*A w/ Smart Entry and Start System *B w/o Smart Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592976N01
3.76,0.292 4.042,0.646 0.281,0.354 18 false i

i.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




c.
B592977C01
5.49,2.646 6.042,2.865 6.042,2.865 5.979,2.646 true 1.604,4.635 2.479,4.76 2.479,4.76 3.292,4.271 true 3.833,4.531 4.677,4.76 4.677,4.76 5.323,4.281 true 1.552,1.646 1.833,2 0.281,0.354 18 false i 4.698,1.656 4.979,2.01 0.281,0.354 18 false ii 0.198,1.229 0.479,1.583 0.281,0.354 18 false iii 4.146,0.813 4.427,1.167 0.281,0.354 18 false iii 4.479,0.813 4.76,1.167 0.281,0.354 18 false iii 6.24,0.219 6.521,0.573 0.281,0.354 18 false iii 2.135,0.479 2.448,0.677 0.313,0.198 10 false *1 2.719,0.396 3.031,0.594 0.313,0.198 10 false *1 4.635,0.323 4.948,0.521 0.313,0.198 10 false *1 0.563,3.698 0.844,4.052 0.281,0.354 18 false iv 6.094,2.833 6.406,3.031 0.313,0.198 10 false *a 4.635,4.781 4.948,4.979 0.313,0.198 10 false *b 2.417,4.813 2.729,5.01 0.313,0.198 10 false *b
*1 Roof Side Inner Garnish Clip - -
*a Claw (A) *b Claw (B)
V113147

Remove in this Direction - -


i.

Using needle-nose pliers, remove the pins from the clips.


ii.

Using 2 screwdrivers, disengage the claws (A) of each clip and separate the clips from the vehicle body as shown in the illustration.

HINT:

Separate the clips and curtain shield airbag assembly from the vehicle body as a unit.



iii.

Remove the 4 bolts.


iv.

While holding the curtain shield airbag assembly, disengage the hooks and the claws (B), and remove the curtain shield airbag assembly.



d.
B592978

i.

Remove the roof side inner garnish clips from the curtain shield airbag assembly.