Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C6B9F  Rear Motor Shutdown Stuck Off  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects malfunctions which prevent the rear inverter shutdown circuit from shutting down. Detection is performed during the shutdown sequence when the power switch is turned off. If rear inverter operation is detected after a shutdown signal was sent to the rear inverter by the motor generator control ECU (MG ECU), the hybrid vehicle control ECU will determine that there is a malfunction and store this DTC.

The cause of this malfunction may be the following:

Hybrid motor control inverter assembly shutdown circuit (rear motor) internal circuit malfunction
·

Hybrid motor control inverter assembly malfunction

·

Wire harness (SDNR) malfunction

·

Connecter malfunction


Hybrid motor control rear inverter assembly shutdown circuit (rear motor) internal circuit malfunction
·

Hybrid motor control rear inverter assembly malfunction

·

Wire harness (SDNR) malfunction

·

Connecter malfunction



DESCRIPTION

The motor generator control ECU (MG ECU) sends shutdown signals to the rear inverter to cut the power supply to the rear motor. If the power switch is turned off, the motor generator control ECU (MG ECU) will send an SDNR (Rear Motor Shutdown Signal) to the rear inverter, and check the function of the shutdown operation. If a shutdown malfunction is detected, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P1C6B9F Rear Motor Shutdown Stuck Off When the HV gate block function check is performed (when the power switch is turned from on (READY) to off), a shutdown signal is sent to the rear inverter by the motor generator control ECU (MG ECU), but the inverter current and voltage (VH) do not decrease.
(1 trip detection logic)
·

Hybrid motor control inverter assembly

·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P1C6B9F
·

Ready Signal

·

VH-Voltage after Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the rear shutdown signal circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Shut Down Signal Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (SDNR VOLTAGE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SDNR VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458530N01
1.927,1 2.313,1.24 0.385,0.24 1.99,1.042 2.281,1.208 0.292,0.167 10 true O74

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A376569C08
1.5,0.063 1.938,0.344 0.438,0.281 1.948,1.073 2.417,1.781 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 2.323,1.833 2.813,2.021 0.49,0.188 10 false SDNR 1.604,0.146 1.958,0.323 0.354,0.177 10 false O74
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Display Switch Condition Specified Condition
O74-4 (SDNR) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O74 rear hybrid motor control inverter assembly connector.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A378773C07
0.375,3.26 0.823,3.563 0.448,0.302 1.458,0.177 1.896,0.469 0.438,0.292 1.99,1.229 2.604,2.052 true 1.948,3.479 2.563,4.302 true 0.177,0.115 0.49,0.271 0.313,0.156 10 false *a 0.24,2.427 0.552,2.583 0.313,0.156 10 false *b 2.49,2.115 2.948,2.344 0.458,0.229 10 false SDNR 2.438,4.333 2.896,4.563 0.458,0.229 10 false SDNR 1.563,0.26 2.052,0.615 0.49,0.354 10 false O74 0.49,3.354 0.802,3.531 0.313,0.177 10 false A56
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)


Disconnect the O74 rear hybrid motor control inverter assembly connector.


c.

Disconnect the A56 hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Display Switch Condition Specified Condition
O74-4 (SDNR) - A56-18 (SDNR) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Display Switch Condition Specified Condition
O74-4 (SDNR) or A56-18 (SDNR) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A56 hybrid motor control inverter assembly connector.


b.

Reconnect the O74 rear hybrid motor control inverter assembly connector.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR