Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Rear Motor High-voltage Circuit  


DESCRIPTION

The cause of this malfunction may be the high-voltage circuit of the rear motor.

Check the rear motor internal resistance and the connection condition of the high-voltage line between the rear inverter and rear motor to check whether there is an open or short circuit.

Related Parts Check
Area Inspection
Rear motor cable connection check Check for open circuit in the connection condition of the cable from the inverter to the rear motor.
Rear motor, rear motor cable, extension wire Check the rear motor (including cable) internal resistance and the insulation resistance with body ground to check for an open or short circuit.
Rear motor cable Check for open or short in rear motor cable.

WIRING DIAGRAM

A451441E06
1.156,2.417 2.99,2.656 1.833,0.24 10 false : High Voltage Line 2.438,0.458 2.594,0.656 0.156,0.198 10 false W 2.438,0.802 2.594,1 0.156,0.198 10 false U 2.438,1.125 2.594,1.323 0.156,0.198 10 false V 2.677,0.385 2.833,0.583 0.156,0.198 10 false 3 2.677,0.74 2.833,0.938 0.156,0.198 10 false 1 2.667,1.135 2.823,1.333 0.156,0.198 10 false 2 0.865,1.573 1.917,1.74 1.052,0.167 10 false m1 0.865,1.729 3.167,2.125 2.302,0.396 10 false Rear Traction Motor with Transaxle Assembly (Rear Motor (MGR)) 4.906,0.427 5.063,0.625 0.156,0.198 10 false 1 4.917,0.771 5.073,0.969 0.156,0.198 10 false 3 4.917,1.125 5.073,1.323 0.156,0.198 10 false 2 4.896,1.594 5.26,1.792 0.365,0.198 10 false m2 4.906,1.771 6.531,2.177 1.625,0.406 10 false Rear Hybrid Motor Control Inverter Assembly 5.115,0.552 5.271,0.75 0.156,0.198 10 false W 5.115,0.906 5.271,1.104 0.156,0.198 10 false U 5.125,1.25 5.281,1.448 0.156,0.198 10 false V

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (NO. 2 ENGINE ROOM WIRE (REAR MOTOR CABLE) CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminals cover from the rear hybrid motor control inverter assembly.


c.
A475632C01
2.031,0.865 2.323,0.531 2.323,0.531 2.448,0.531 true 2.51,0.479 2.719,0.646 0.208,0.167 10 true *1
*1 Rear Traction Motor Cable


Check that the bolts for the rear traction motor cable are tightened to the specified torque, the rear traction motor cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm)


NOTICE:

Make sure that the tightening torque of the bolt is between 6.4 and 9.6 N*m (65 and 98 kgf*cm).



d.

Disconnect the rear traction motor cable from the rear hybrid motor control inverter assembly.


Procedure1

a.

Check for arc marks at the rear traction motor cable.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the rear traction motor cable to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminals cover to the rear hybrid motor control inverter assembly.



A

2.CHECK REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR (MGR))

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

2.CHECK REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR (MGR))
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminals cover from the rear hybrid motor control inverter assembly.


c.
A475632C01
2.031,0.865 2.323,0.531 2.323,0.531 2.448,0.531 true 2.51,0.479 2.719,0.646 0.208,0.167 10 true *1
*1 Rear Traction Motor Cable


Disconnect the rear traction motor cable to the rear hybrid motor control inverter assembly.


Procedure1

a.
A376644C07
0.417,0.917 0.823,1.177 0.406,0.26 1.344,1.969 1.531,1.698 true 1.063,1.688 1.313,1.5 true 0.781,1.427 1.104,1.271 true 2.427,1.75 2.167,1.542 true 2.458,1.75 2.771,1.906 0.313,0.156 10 false *1 0.281,0.208 0.594,0.365 0.313,0.156 10 false *a 0.604,1.406 0.823,1.615 0.219,0.208 10 false W 0.542,0.969 0.844,1.167 0.302,0.198 10 false m2 0.938,1.677 1.188,1.885 0.25,0.208 10 false V 1.24,1.969 1.458,2.177 0.219,0.208 10 false U
*1 Shield Ground
*a Rear Motor Cable
(Rear Hybrid Motor Control Inverter Assembly)


Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the rear motor (MGR) temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(m2)Location & Routing

Click Connector(m2)Body>Rear Traction Motor Cable>Rear Hybrid Motor Control Inverter Assembly

m2-1 (W) - m2-2 (V) Ignition switch off 192.6 to 212.3 mΩ
m2-2 (V) - m2-3 (U) Ignition switch off 192.6 to 212.3 mΩ
m2-3 (U) - m2-1 (W) Ignition switch off 192.6 to 212.3 mΩ


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F))



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(m2)Location & Routing

Click Connector(m2)Body>Rear Traction Motor Cable>Rear Hybrid Motor Control Inverter Assembly

m2-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
m2-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
m2-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the rear traction motor cable to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminals cover from the rear hybrid motor control inverter assembly.



OK

REAR MOTOR HIGH-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR TRACTION MOTOR CABLE CONNECTION CONDITION)
3.CHECK REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR TRACTION MOTOR CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear suspension member sub-assembly.

HINT:

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>REMOVAL



c.
A458533

Check that the bolts for the rear traction motor cable are tightened to the specified torque, the rear traction motor cable is connected securely, and there are no contact problems.

Specified Condition:

T=10 N*m (102 kgf*cm)


NOTICE:

Make sure that the tightening torque of the bolt is between 8 and 12 N*m (82 and 122 kgf*cm).



d.

Disconnect the rear traction motor cable from the rear traction motor.


Procedure1

a.

Check for arc marks at the bolts for the rear traction motor cable.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the rear traction motor cable to the rear traction motor.


b.

Install the rear suspension member sub-assembly.



A

4.CHECK REAR TRACTION MOTOR CABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

CONNECT SECURELY

4.CHECK REAR TRACTION MOTOR CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear suspension member sub-assembly.

HINT:

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>REMOVAL



c.

Disconnect the rear traction motor cable.

HINT:

Click hereDrivetrain>Q510 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

a.
A376645C07
0.427,3.219 0.823,3.49 0.396,0.271 0.385,0.875 0.802,1.125 0.417,0.25 0.698,1.406 1.094,1.281 true 0.979,1.781 1.313,1.5 true 1.302,2.042 1.531,1.729 true 2.5,1.573 2.177,1.542 true 2.865,3.906 2.542,3.875 true 0.708,3.844 1.104,3.719 true 1.01,4.198 1.344,3.917 true 1.365,4.427 1.594,4.115 true 2.573,1.49 2.885,1.646 0.313,0.156 10 false *1 0.458,0.229 0.771,0.385 0.313,0.156 10 false *a 0.5,2.677 0.813,2.833 0.313,0.156 10 false *b 2.917,3.844 3.229,4 0.313,0.156 10 false *1 0.552,3.281 0.865,3.438 0.313,0.156 10 false m1 0.51,0.927 0.823,1.083 0.313,0.156 10 false m2 0.542,1.354 0.854,1.51 0.313,0.156 10 false W 0.833,1.792 1.146,1.948 0.313,0.156 10 false V 1.188,2.083 1.5,2.24 0.313,0.156 10 false U 0.573,3.833 0.885,3.99 0.313,0.156 10 false U 0.885,4.177 1.198,4.333 0.313,0.156 10 false V 1.25,4.448 1.563,4.604 0.313,0.156 10 false W
*1 Shield Ground
*a Rear Traction Motor Cable
(to Rear Hybrid Motor Control Inverter Assembly)
*b Rear Traction Motor Cable
(to Rear Traction Motor)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(m2,m1)Location & Routing

Click Connector(m2)Body>Rear Traction Motor Cable>Rear Hybrid Motor Control Inverter Assembly

Click Connector(m1)Body>Rear Traction Motor Cable>Rear Traction with Transaxle Motor Assembly

m2-1 (W) or m1-3 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher
m2-2 (V) or m1-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
m2-3 (U) or m1-1 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher


NOTICE:

Wrap the terminals of three-phase AC cable with insulating tape to avoid them coming into contact with body ground.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(m2,m1)Location & Routing

Click Connector(m2)Body>Rear Traction Motor Cable>Rear Hybrid Motor Control Inverter Assembly

Click Connector(m1)Body>Rear Traction Motor Cable>Rear Traction with Transaxle Motor Assembly

m2-1 (W) - m1-3 (W) Ignition switch off Below 1 Ω
m2-2 (V) - m1-2 (V) Ignition switch off Below 1 Ω
m2-3 (U) - m1-1 (U) Ignition switch off Below 1 Ω
m2-1 (W) - m1-1 (U) Ignition switch off 100 kΩ or higher
m2-2 (V) - m1-3 (W) Ignition switch off 100 kΩ or higher
m2-3 (U) - m1-2 (V) Ignition switch off 100 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the rear traction motor cable.


b.

Install the rear suspension member sub-assembly.



OK

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

NG

REPLACE REAR TRACTION MOTOR CABLE