Home › Drivetrain › Q510 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE
RM3700E _52 Drivetrain _093740 Q510 HYBRID TRANSMISSION / TRANSAXLE _0441870 MOTOR CABLE A

Q510 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442346N01
0.833,3 1.167,3 false 0.656,2.792 0.938,3.146 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SERVICE PLUG GRIP G3834 - - -

C430368N01
4.958,1.531 5.292,1.531 false 4.625,3.74 4.958,3.74 false 5.375,1.406 5.656,1.76 0.281,0.354 18 false 2 5.063,3.615 5.344,3.969 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 DECK BOARD ASSEMBLY 58410B - - -
3 REAR DECK FLOOR BOX 64993 - - -

C442347N02
5.896,1.771 5.896,2.104 false 4.365,3.042 4.615,3.042 false 6.469,0.26 6.802,0.26 false 1.917,2.25 1.75,2.25 1.75,2.25 1.656,1.844 false 3.531,2.094 3.844,2.292 0.313,0.198 10 false x5 2.135,1.115 2.448,1.313 0.313,0.198 10 false x5 0.875,2.052 1.188,2.25 0.313,0.198 10 false x2 3.635,0.25 3.948,0.448 0.313,0.198 10 false x6 5.833,2.125 6.115,2.479 0.281,0.354 18 false 4 4.969,2.875 5.573,3.229 0.604,0.354 18 false 5, 8 6.229,0.094 6.51,0.448 0.281,0.354 18 false 6 2.25,2.104 2.531,2.458 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

4 HYBRID INVERTER PROTECTOR ASSEMBLY G92D0 - - -
5 REMOVE INVERTER TERMINAL COVER G9223 (Click here) - -
6 CHECK TERMINAL VOLTAGE - (Click here) - -
7 REAR TRACTION MOTOR CABLE G1149 (Click here) - -
8 TEMPORARILY TIGHTEN INVERTER TERMINAL COVER G9223 (Click here) - -

C442348N02
4.917,4.427 5.25,4.427 false 4.844,1.823 4.927,2.052 4.927,2.052 5.094,2.052 false 3.302,2.542 3.552,2.438 3.552,2.438 3.719,2.438 false 3.177,1.448 3.49,1.229 3.49,1.229 3.656,1.229 false 5.333,4.25 5.615,4.604 0.281,0.354 18 false 9 5.385,1.875 5.958,2.208 0.573,0.333 18 false 10 4.188,2.25 4.667,2.656 0.479,0.406 18 false 11 4.063,2.313 4.281,2.521 0.219,0.208 10 false ● 4,1.031 4.479,1.354 0.479,0.323 18 false 12 3.104,2.979 3.417,3.177 0.313,0.198 10 false x3 1.813,1.781 2.125,1.979 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

9 REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY G1050 - - -
10 REAR TRACTION MOTOR BREATHER PLUG 30900T (Click here) - -
11 MOTOR CABLE TERMINAL CAP G114D (Click here) - -
12 REAR TRACTION MOTOR CABLE G1149 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear traction motor cable removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 64993 3.REMOVE REAR DECK FLOOR BOX

Hide G92D0 4.REMOVE HYBRID INVERTER PROTECTOR ASSEMBLY

Hide G9223 5.REMOVE INVERTER TERMINAL COVER

Z101186

Click here(Click here)

Hide G1149 7.DISCONNECT REAR TRACTION MOTOR CABLE

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C442349C03
1.052,2.542 1.385,2.542 true 1.427,2.448 1.646,2.625 0.219,0.177 10 true *a 0.458,0.083 0.74,0.365 0.281,0.281 18 true i 2.844,1.281 3.094,1.552 0.25,0.271 18 true ii 3.406,0.073 3.958,0.375 0.552,0.302 18 true iii, iv
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 5 bolts and disconnect the rear traction motor cable from the rear hybrid motor control inverter assembly.

NOTICE:
·

Keep the rear traction motor cable terminals and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the rear traction motor cable.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.

·

Cover the hole where the rear traction motor cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.




ii.

Disengage the clamp.


iii.

Disengage the clamp.


iv.

Remove the 2 nuts from the vehicle body, and pass the rear traction motor cable through to the outside of the vehicle body.



Hide G9223 8.TEMPORARILY INSTALL INVERTER TERMINAL COVER

Z101186

Click here(Click here)

Hide G1050 9.REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

Hide 30900T 10.REMOVE REAR TRACTION MOTOR BREATHER PLUG

Z101186

Click here(Click here)

Hide G114D 11.REMOVE MOTOR CABLE TERMINAL CAP

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C442350E01
0.479,0.125 0.75,0.417 0.271,0.292 18 true i 3.833,0.125 4.104,0.417 0.271,0.292 18 true ii

i.

Remove the 3 bolts and slide the connector cover assembly as shown in the illustration.


ii.

Disengage the 2 claws to remove the motor cable terminal cap from the rear traction motor with transaxle assembly.



Hide G1149 12.REMOVE REAR TRACTION MOTOR CABLE

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C442351C01
1.667,2.583 1.833,2.583 1.833,2.583 1.896,2.375 true 0.5,0.146 0.781,0.5 0.281,0.354 18 false i 3.583,0.146 3.865,0.5 0.281,0.354 18 false ii 1.469,2.5 1.729,2.698 0.26,0.198 10 false *a
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 3 bolts and disconnect the rear traction motor cable from the rear traction motor with transaxle assembly.

NOTICE:
·

Keep the rear traction motor cable and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the rear traction motor cable.

·

Cover the hole where the rear traction motor cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.




ii.

Disengage the clamp.