Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FXE) › 2020.08–2021.07
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0444422 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FXE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FXE)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446082N01
6.531,0.25 6.865,0.25 false 5.24,3.083 5.573,3.083 false 3.521,3.917 3.854,3.917 false 1.458,2.167 1.792,2.167 false 0.854,3.5 0.854,3.844 false 1.604,4.229 1.979,4.469 0.375,0.24 10 false x4 2.198,4.354 2.573,4.594 0.375,0.24 10 false x4 2.688,4.208 3.063,4.448 0.375,0.24 10 false x9 4.656,3.75 5.031,3.99 0.375,0.24 10 false x2 1.875,2.01 2.25,2.375 0.375,0.365 18 false 4 6.344,0.104 6.719,0.469 0.375,0.365 18 false 5 5.052,2.938 5.427,3.302 0.375,0.365 18 false 1 1.104,1.583 1.479,1.823 0.375,0.24 10 false x2 0.792,3.865 1.167,4.229 0.375,0.365 18 false 2 3.333,3.781 3.708,4.146 0.375,0.365 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT WHEELS - - - -
2 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
3 REAR ENGINE UNDER COVER LH 51442C - - -
4 REAR ENGINE UNDER COVER RH 51441C - - -
5 DRAIN HYBRID TRANSAXLE FLUID - - (Click here) -

C445401N01
1.583,1.708 1.75,1.708 1.75,1.708 2.208,1.354 false 4.292,4 4.708,4 false 4.823,0.594 5.406,0.594 false 6.063,1.76 6.219,1.427 6.219,1.427 6.385,1.427 false 5.354,3.198 5.656,3.552 5.656,3.552 5.823,3.552 false 1.667,0.667 2.74,0.667 false 6.135,2.563 6.448,2.563 false 5.969,0.833 6.125,0.583 6.125,0.583 6.292,0.583 false 6.292,3.417 6.573,3.771 0.281,0.354 18 false 6 5.656,0.469 5.938,0.823 0.281,0.354 18 false 7 6.698,1.302 6.979,1.656 0.281,0.354 18 false 8 1.469,0.51 1.75,0.865 0.281,0.354 18 false 9 4.781,3.875 5.229,4.229 0.448,0.354 18 false 10 1.302,1.531 1.75,1.885 0.448,0.354 18 false 11 6.125,3.448 6.281,3.646 0.156,0.198 10 false ● 6.5,2.469 6.656,2.667 0.156,0.198 10 false ● 6.333,0.51 6.656,0.677 0.323,0.167 10 false *1 4.479,4.469 4.802,4.635 0.323,0.167 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

6 FRONT AXLE SHAFT NUT 43502H (Click here) - -
7 FRONT SPEED SENSOR 89543 (Click here) - -
8 TIE ROD END SUB-ASSEMBLY 45047 (Click here) - -
9 FRONT STABILIZER LINK ASSEMBLY 48810 (Click here) - -
10 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 48069 - - -
11 SEPARATE FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -

*1 FRONT FLEXIBLE HOSE - -
● Non-reusable part - -

C445421N01
3.667,0.979 4,0.979 false 4.333,1.875 4.531,1.531 4.531,1.531 4.74,1.531 false 4.438,0.865 4.99,1.219 0.552,0.354 18 false 13 5.104,1.417 5.656,1.771 0.552,0.354 18 false 12 4.344,0.906 4.5,1.104 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

12 REMOVE FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -
13 FRONT DRIVE SHAFT HOLE SNAP RING 43420G (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 3.REMOVE ENGINE UNDER COVER LH

Hide 51441C 4.REMOVE ENGINE UNDER COVER RH

Hide 43502H 6.REMOVE FRONT AXLE SHAFT NUT

a.
C446084N01
2.104,1.563 2.406,1.167 true 0.396,0.073 0.625,0.396 0.229,0.323 18 false i 3.667,0.031 3.854,0.354 0.188,0.323 18 true ii 1.927,1.604 2.292,1.771 0.365,0.167 10 true SST

i.

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.



ii.

While applying the brakes, remove the front axle shaft nut.



Hide 89543 7.SEPARATE FRONT SPEED SENSOR

Z101186

Click here(Click here)

Hide 45047 8.SEPARATE TIE ROD END SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 48810 9.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Z101186

Click here(Click here)

Hide 48069 10.SEPARATE FRONT LOWER NO.1 SUSPENSION ARM SUB-ASSEMBLY

Hide 11.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 43420 12.REMOVE FRONT DRIVE SHAFT ASSEMBLY

a.
C445423N01
3.875,1.313 3.333,1.521 3.333,1.521 3.698,0.948 true 0.469,0.104 0.75,0.458 0.281,0.354 18 false i 3.052,1.469 3.365,1.656 0.313,0.188 10 false SST

i.

Using SST, remove the front drive shaft assembly.

SST
09520-01011  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the front drive shaft oil seal.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly.





Hide 43420G 13.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C445400N01
0.406,0.083 0.688,0.438 0.281,0.354 18 false i

i.

Using a screwdriver, remove the front drive shaft hole snap ring.