Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0444428 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446093N02
5.563,1.385 5.813,1.052 5.813,1.052 5.979,1.052 false 3.74,2.375 3.906,2.375 3.906,2.375 4.25,1.75 false 1.5,2 1.667,2 1.667,2 1.75,1.479 false 0.667,2.083 0.833,2.083 0.833,2.083 1,1.667 false 6.063,0.885 6.344,1.24 0.281,0.354 18 false 1 1.323,1.813 1.604,2.167 0.281,0.354 18 false 2 3.552,2.25 3.833,2.604 0.281,0.354 18 false 3 3.406,2.292 3.688,2.646 0.281,0.354 10 false ● 0.49,2.021 0.771,2.375 0.281,0.354 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 REAR SKID CONTROL SENSOR 89544E (Click here)
3 REAR AXLE SHAFT NUT 42312B (Click here)

*1 NO. 2 PARKING BRAKE WIRE ASSEMBLY - -
● Non-reusable part - -

C445433N01
3.479,2.375 3.646,2.375 3.646,2.375 4.5,2.125 false 3.198,2.208 3.479,2.563 0.281,0.354 18 false 4 4.76,1.573 5.042,1.927 0.281,0.354 10 false x4 4.948,1.708 5.229,2.063 0.281,0.354 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

4 REAR DRIVE SHAFT ASSEMBLY 42340B (Click here) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 89544E 2.REMOVE REAR SKID CONTROL SENSOR

Z101186

Click here(Click here)

Hide 42312B 3.REMOVE REAR AXLE SHAFT NUT

Z101186

Click here(Click here)

Hide 42340B 4.REMOVE REAR DRIVE SHAFT ASSEMBLY

a.
C450150C02
2.021,1.542 2.021,1.208 2.021,1.208 1.938,1.208 true 1.938,1.24 2.021,1.24 true 6.292,0.667 5.854,1.5 5.854,1.5 6.427,0.927 true 0.417,0.052 0.823,0.323 0.406,0.271 18 true i, ii 3.948,0.073 4.25,0.313 0.302,0.24 18 true iii 0.438,2.073 0.677,2.354 0.24,0.281 18 true iv 3.938,2.083 4.49,2.344 0.552,0.26 18 true v, vi 1.948,1.583 2.135,1.771 0.188,0.188 10 true *a 5.74,1.5 5.927,1.688 0.188,0.188 10 false *a
*a Matchmark - -


i.

Put matchmarks on the rear drive shaft assembly and differential side gear shaft sub-assembly.


ii.

Remove the 4 nuts and 4 washers.


iii.

Put matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.


iv.

Push the rear drive shaft inboard joint assembly toward the outside of the vehicle and remove the rear drive shaft assembly from the differential side gear shaft sub-assembly.

NOTICE:

Do not damage the rear drive shaft inboard joint boot.



v.

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

NOTICE:
·

Do not damage the rear drive shaft outboard joint boot.

·

Do not drop the rear drive shaft assembly.




vi.

If it is difficult to separate the rear drive shaft assembly from the rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.