Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for AWD) › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441828 REAR AXLE HUB(for AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444357N04
6.563,0.188 6.833,0.188 false 4.865,1.26 5.281,1.26 false 5.26,3.396 6.167,2.521 6.167,2.521 6.313,2.521 false 5.031,4.063 5.406,4.063 false 3.531,2.083 3.948,2.083 false 1.333,2.115 1.333,2.448 false 3.594,0.656 4.01,0.656 false 4.167,3.344 3.99,3.646 3.99,3.646 3.823,3.646 false 1.833,2.833 2,2.833 2,2.833 2.333,2 false 6.052,0.052 6.719,0.406 0.667,0.354 18 false 1, 2 5.552,1.125 5.771,1.427 0.219,0.302 18 false 6 6.76,2.385 6.979,2.688 0.219,0.302 18 false 5 4.833,3.927 5.052,4.229 0.219,0.302 18 false 7 4.01,2.021 4.385,2.188 0.375,0.167 10 false *1 1.385,2.448 1.604,2.75 0.219,0.302 18 false 4 1.885,1.042 2.26,1.208 0.375,0.167 10 false x2 0.198,0.729 0.573,0.896 0.375,0.167 10 false x4 3.396,0.521 3.615,0.823 0.219,0.302 18 false 3 3.531,3.521 3.885,3.833 0.354,0.313 18 false 8 1.667,2.75 2.042,2.917 0.375,0.167 10 false *2 6.594,2.479 6.813,2.781 0.219,0.302 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 PARKING BRAKE ACTUATOR ASSEMBLY 46310B - - -
4 REAR SKID CONTROL SENSOR 89544E (Click here) - -
5 REAR AXLE SHAFT NUT 42312B (Click here) - -
6 REAR DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
7 REAR DISC 42431 (Click here) - -
8 REAR AXLE HUB AND BEARING ASSEMBLY 42450B (Click here) - -

*1 REAR BRAKE DUST COVER *2 REAR AXLE BEARING RETAINER
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Parking assist monitor system Memorize steering angle neutral point (Click here)
Panoramic view monitor system (Click here)

HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISABLE BRAKE CONTROL

Hide 46310B 3.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Hide 89544E 4.REMOVE REAR SKID CONTROL SENSOR

Z101186

Click here(Click here)

Hide 42312B 5.REMOVE REAR AXLE SHAFT NUT

a.
C444360N01
2.927,1.083 3.302,0.969 false 3.354,0.875 3.667,1.031 0.313,0.156 10 true SST 0.406,0.073 0.781,0.375 0.375,0.302 18 false i 3.969,0.073 4.344,0.375 0.375,0.302 18 false ii

i.

Using SST and a hammer, release the staked part of the rear axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the rear axle shaft nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.



ii.

Using a 30 mm deep socket wrench. While applying the brakes, remove the rear axle shaft nut.



Hide 6.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 42431 7.REMOVE REAR DISC

Z101186

Click here(Click here)

Hide 42450B 8.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

a.
C444361C01
2.729,0.365 3.01,0.365 3.01,0.365 3.01,0.781 true 2.865,0.635 3.01,0.635 true 0.375,0.042 0.656,0.396 0.281,0.354 18 false i 3.969,0.083 4.469,0.406 0.5,0.323 18 true ii, iii 2.906,0.813 3.156,0.979 0.25,0.167 10 true *a
*a Matchmark - -


i.

Put matchmarks on the rear drive shaft assembly and the rear axle hub and bearing assembly.


ii.

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

NOTICE:
·

Do not damage the rear drive shaft outboard joint boot.

·

Do not push the rear axle hub and bearing assembly towards the outside of the vehicle any further than necessary.




iii.

If it is difficult to separate the rear drive shaft assembly rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.



b.
C444363N01
0.104,0.031 0.385,0.385 0.281,0.354 18 false i

i.

Remove the 4 bolts, rear axle hub and bearing assembly, rear axle bearing retainer and rear brake dust cover from the rear axle carrier sub-assembly